Document Outline

• 8220/8240 frequency inverters power range 0.37 ... 90 kW
  • These Operating Instructions are vakid for ...
  • Contents
    • 1 Preface and general information
      • 1.1 How to use these Operating Instructions
        • 1.1.1 Terminology used
        • 1.1.2 What is new?
      • 1.2 Scope of delivery
      • 1.3 Legal regulations
    • 2 Safety information
      • 2.1 General safety information
      • 2.2 Layout of the safety information
      • 2.3 Residual hazards
    • 3 Technical data
      • 3.1 General data/ application conditions
      • 3.2 Rated data (operation with 150 % overload)
        • 3.2.1 Types 8221 to 8224
        • 3.2.2 Types 8225 to 8227
        • 3.2.3 Types 8241 to 8243
        • 3.2.4 Types 8244 to 8246
      • 3.3 Rated data (operation wih 120 % overload)
        • 3.3.1 Operating conditions
        • 3.3.2 Types 822X
        • 3.3.3 Types 824X
      • 3.4 Fuses and cable cross-sections for single drives
        • 3.4.1 Operation of controllers in a UL-approved system
        • 3.4.2 Operation with 150 % overload
        • 3.4.3 Operation with 120 % overload
      • 3.5 Dimensions
    • 4 Installation
      • 4.1 Mechanical installation
        • 4.1.1 Important notes
        • 4.1.2 Standard assembly with fixing brackets
        • 4.1.3 Assembly of the variant 82XX-C-V003 fl Cold Platefl
          • 4.1.3.1 Assembly preparation
          • 4.1.3.2 Assembly 822X-C-V003
          • 4.1.3.3 Assembly 824X-C-V003
      • 4.2 Electrical installation
        • 4.2.1 Important notes
        • 4.2.2 Power connections
          • 4.2.2.1 Mains connection
          • 4.2.2.2 Motor connection
          • 4.2.2.3 Connection diagram
        • 4.2.3 Control connections
          • 4.2.3.1 Control cables
          • 4.2.3.2 Assignment of the control terminals
          • 4.2.3.3 Connection diagrams
      • 4.3 Installation of a CE-typical drive system
    • 5 Commissioning
      • 5.1 Before you switch on
      • 5.2 Short set-up with factory setting
        • 5.2.1 Switch-on sequence
        • 5.2.2 Factory setting of the most important drive parameters
      • 5.3 Adapt machine data
        • 5.3.1 Determine speed range (fdmin, fdmax)
        • 5.3.2 Adjustment of acceleration and deceleration times (Tir, Tif)
        • 5.3.3 Setting of the current limit (Imax)
      • 5.4 Optimize the operating characteristic of the drive
        • 5.4.1 Select the control mode
        • 5.4.2 Optimize control modes
          • 5.4.2.1 Optimize motor-current control
          • 5.4.2.2 Optimize V/ f-characteristic control
    • 6 During operation
    • 7 Configuration
      • 7.1 Basics
      • 7.2 Code table
    • 8 Troubleshooting and fault elimination
      • 8.1 Troubleshooting
        • 8.1.1 Display at the controller
        • 8.1.2 Display at the operating module
        • 8.1.3 Maloperation of the drive
      • 8.2 Fault analysis using the history buffer
      • 8.3 Fault indications
      • 8.4 Reset of fault indications
    • 9 Accessories (Survey)
      • 9.1 Accessories for all types
      • 9.2 Software
      • 9.3 Type-specific accessories
        • 9.3.1 Types 8221 -8224
        • 9.3.2 Types 8225 -8227
        • 9.3.3 Types 8241 -8244
        • 9.3.4 Types 8245 -8246
    • 10 Index