Document Outline

• E84AYCIB communication module (INTERBUS)
  • Contents
    • 1 About this documentation
      • 1.1 Document history
      • 1.2 Conventions used
      • 1.3 Terminology used
      • 1.4 Notes used
    • 2 Safety instructions
      • 2.1 General safety instructions and application notes
      • 2.2 Device- and application-specific safety instructions
      • 2.3 Residual hazards
    • 3 Product description
      • 3.1 Application as directed
      • 3.2 Identification
      • 3.3 Product features
      • 3.4 Terminals and interfaces
    • 4 Technical data
      • 4.1 General data and operating conditions
      • 4.2 Protective insulation
      • 4.3 Protocol data
      • 4.4 Communication time
      • 4.5 Dimensions
    • 5 Installation
      • 5.1 Mechanical installation
        • 5.1.1 Mounting for standard devices 0.25 kW and 0.37 kW
        • 5.1.2 Mounting for standard devices from 0.55 kW onwards
        • 5.1.3 Replacing the communication module
      • 5.2 Electrical installation
        • 5.2.1 EMC-compliant wiring
        • 5.2.2 Network topology
        • 5.2.3 INTERBUS connection
        • 5.2.4 Specification of the bus cable
        • 5.2.5 Bus cable length
        • 5.2.6 External voltage supply
    • 6 Commissioning
      • 6.1 Before initial switch-on
      • 6.2 Possible settings through DIP switch
        • 6.2.1 Setting the number of process data words (PD)
        • 6.2.2 Setting the number of parameter data words (PCP)
        • 6.2.3 Setting the baud rate
      • 6.3 Settings in the »Engineer«
      • 6.4 Initial switch-on
    • 7 Data transfer
    • 8 Process data transfer
      • 8.1 Access to process data / PDO mapping
      • 8.2 Preconfigured port interconnection of the process data objects (PDO)
      • 8.3 Freely configurating the port interconnection of the process data objects (PDO)
    • 9 Parameter data transfer
      • 9.1 Addressing of the parameter data
      • 9.2 Initialising PCP communication
      • 9.3 Supported PMS services
        • 9.3.1 Initiate
        • 9.3.2 Abort
        • 9.3.3 Reject
        • 9.3.4 Read / Write
        • 9.3.5 Get-OD
        • 9.3.6 Identify
        • 9.3.7 Status
    • 10 Monitoring
    • 11 Diagnostics
      • 11.1 LED status displays
        • 11.1.1 Module status displays
        • 11.1.2 Fieldbus status displays
      • 11.2 Querying the current bus status
      • 11.3 Diagnostic data
    • 12 Error messages
      • 12.1 Short overview (A-Z) of the INTERBUS error messages
      • 12.2 Possible causes and remedies
        • Lost connection to 8400 base device [0x01bc3100]
        • Memory not accessible [0x01bc5531]
        • Memory read error [0x01bc5532]
        • Memory write error [0x01bc5533]
        • Internal error [0x01bc6010]
        • Internal error [0x01bc6011]
        • Internal error [0x01bc6100]
        • Internal error [0x01bc6101]
        • Invalid parameter set [0x01bc641f]
        • Lenze setting loaded [0x01bc6420]
        • Invalid module configuration [0x01bc6430]
        • Invalid configuration [0x01bc8125]
        • Communication stack reset [0x01bc8126]
        • Invalid initialisation [0x01bc8127]
        • Data exchange stopped [0x01bc8131]
    • 13 Parameter reference
      • 13.1 Parameters of the communication module
        • C13850 | All words to master
        • C13851 | All words from master
        • C13852 | All words to standard device
        • C13853 | All words from standard device
        • C13860 | Active settings
        • C13861 | Bus status
        • C13862 | Counter
        • C13863 | Active baud rate
        • C13880 | Reaction on communication failure
        • C13881 | Monitoring time for Interbus communication failure
        • C13885 | Delete process data
        • C13892 | PCP - length
        • C13893 | Process data length
        • C13894 | Baud rate
        • C13900 | Firmware product type
        • C13901 | Firmware compilation date
        • C13902 | Firmware version
        • C13920 | Display DIP switch setting
      • 13.2 Table of attributes
    • 14 Index