Document Outline

• EDSLCMX3024-SPS
  • This documentation is valid for ...
  • Document history
  • Contents
    • 1 Safety instructions
      • 1.1 General safety and application notes for Lenze motor starters
      • 1.2 Residual hazards
      • 1.3 Definition of notes used
    • 2 Device description
      • 2.1 ELCAMWIxxx4SNNPSNN motor starter
      • 2.2 ELCAMZIxxx4SNNPSNN motor starter
    • 3 Technical data
      • 3.1 General data and operating conditions
      • 3.2 Rated data
    • 4 Mechanical installation
      • 4.1 Dimensions
      • 4.2 Mounting clearance
    • 5 Electrical installation
      • 5.1 Important notes
      • 5.2 Basic circuit diagram
        • 5.2.1 ELCAMWIxxx4SNNPSNN motor starter
        • 5.2.2 ELCAMZIxxx4SNNPSNN motor starter
      • 5.3 Mains connection
      • 5.4 Motor connection
        • 5.4.1 ELCAMWIxxx4SNNPSNN motor starter
        • 5.4.2 ELCAMZIxxx4SNNPSNN motor starter
      • 5.5 Safety engineering
      • 5.6 Control terminals
      • 5.7 Communication
      • 5.8 Final works
    • 6 PROFIsafe on board
      • 6.1 Technical data
        • 6.1.1 General data and operating conditions
        • 6.1.2 Protective insulation
        • 6.1.3 Communication times
      • 6.2 Establishing of PROFIBUS communication
        • 6.2.1 Configuration of the host
        • 6.2.2 Safe addressing
        • 6.2.3 Addressing
      • 6.3 Process data transfer
        • 6.3.1 Device control
      • 6.4 Parameter data transfer
        • 6.4.1 DRIVECOM parameter data channel ( DP-V0, cyclic)
        • 6.4.2 PROFIdrive parameter data channel ( DP-V1, acyclic)
        • 6.4.3 PROFIdrive parameter data channel ( PCW)
        • 6.4.4 Parameter set transfer
      • 6.5 Commissioning
      • 6.6 Code table
        • 6.6.1 Communication-relevant Lenze codes
        • 6.6.2 Monitoring
        • 6.6.3 Diagnostics
      • 6.7 Appendix
        • 6.7.1 Special characteristics for the use of Lenze standard devices
        • 6.7.2 Consistent parameter data
    • 7 Safety engineering
      • 7.1 Basics
        • 7.1.1 Introduction
        • 7.1.2 Drive-based safety with L-force | LCU
        • 7.1.3 Terms and abbreviations of the safety engineering
        • 7.1.4 Safety instructions
        • 7.1.5 Hazard and risk analysis
        • 7.1.6 Standards
        • 7.1.7 Overview of sensors
      • 7.2 Test certificate
      • 7.3 Display elements
      • 7.4 Safe inputs and safe outputs
        • 7.4.1 Overview
        • 7.4.2 Technical data
        • 7.4.3 Safe inputs
        • 7.4.4 Safe outputs
        • 7.4.5 Connection plans
      • 7.5 Safety functions
        • 7.5.1 Function mode
        • 7.5.2 Description
        • 7.5.3 Error states
        • 7.5.4 Safe torque off
        • 7.5.5 Safe PROFIsafe connection
      • 7.6 Commissioning
      • 7.7 Acceptance
        • 7.7.1 Description
        • 7.7.2 Periodic inspections
    • 8 Commissioning
      • 8.1 Preconditions
        • 8.1.1 The E82ZBB diagnosis terminal
        • 8.1.2 Configuration of the host
      • 8.2 Before switching on
      • 8.3 Switch-on sequence
      • 8.4 Switching over between normal operation and reversing operation
      • 8.5 Code table
    • 9 Troubleshooting and fault elimination
      • 9.1 Status display
      • 9.2 Malfunction of the drive
      • 9.3 Fault messages