Longshine LCS-8056C2 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for LCS-8056C2 Longshine
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 162 |
| Size: | 784 KB |
Show table of contents
Read manual
Document Outline
- Introduction
- Syntax and Procedures
- Data Command Set
- Command Guidelines
- Data Commands
- Generic Modem Control
- Z - Reset to Default Configuration
- +FCLASS - Select Active Service Class
- +VCID - Caller ID (CID)
- +VRID - Report Retrieved Caller ID (CID)
- \N - Operating Mode
- &F - Set to Factory-Defined Configuration
- &T - Local Analog Loopback Test
- I - Request Identification Information
- +GMI - Request Manufacturer Identification
- +GMM - Request Model Identification
- +GMR - Request Revision Identification
- +GSN - Request Product Serial Number Identification
- +GOI - Request Global Object Identification
- +GCAP - Request Complete Capabilities List
- +GCI - Country of Installation
- DTE-Modem interface commands
- E - Command Echo
- Q - Quiet Results Codes Control
- V - Result Code Form
- W - Connect Message Control
- X - Extended Result Codes
- &C - RLSD Behavior
- &D - DTR Behavior
- &K - Flow Control
- &M - Asynchronous/Synchronous Mode Selection
- &Q - Sync/Async Mode
- +IPR - Fixed DTE Rate
- +IFC - DTE-Modem Local Flow Control
- +ILRR - DTE-Modem Local Rate Reporting
- Call Control
- D - Dial
- T - Set Tone Dial Default
- P - Set Pulse Dial Default
- A - Answer
- H - Disconnect (Hang-Up)
- O - Return to On-Line Data Mode
- L - Speaker Volume
- M - Speaker Control
- &G - Select Guard Tone
- &P - Select Pulse Dial Make/Break Ratio
- &V - Display Current Configuration and Stored Profile
- &W - Store Current Configuration
- *B - Display Blacklisted Numbers
- *D - Display Delayed Numbers
- Modulation Control Commands
- Error Control Commands
- Data Compression Commands
- V.8/V.8bis Commands
- Synchronous Access Mode Commands
- Diagnostic and Test Commands
- V.92 +P and –Q Commands
- +PCW - Call Waiting Enable
- +PMH - Modem-on-Hold Enable
- +PMHT – Modem-on-Hold Timer
- +PMHR - Initiate Modem-on-Hold
- +PIG - PCM Upstream Ignore
- +PMHF - V.92 Modem-on-Hold Hook Flash
- +PQC - V.92 Phase 1 and Phase 2 Control
- +PSS - Use Short Sequence
- -QCPC - Force Full Startup Procedure Next Connection
- -QCPS - Enable Quick Connect Profile Save
- Generic Modem Control
- S-Parameters
- Factory Defaults
- S-Parameter Definitions
- S0 - Number of Rings to Automatic Answer
- S1 - Ring Counter
- S2 - Escape Character
- S3 - Line Termination Character
- S4 - Response Formatting Character
- S5 - Command Line Editing Character
- S6 - Wait Time for Dial Tone Before Blind Dialing
- S7 - Wait Time For Carrier After Dial, For Silenc
- S8 - Pause Time For Dial Delay
- S10 - Lost Carrier To Hang Up Delay
- S11 - DTMF Tone Duration
- S12 - Escape Prompt Delay (EPD)
- S18 - Test Timer
- S28 - Select Pulse Dial/Make/Break Ratio
- S29 - Flash Dial Modifier Time
- S30 - Disconnect Inactivity Timer
- S46 - Data Compression Control
- S95 - Extended Result Codes Control
- S210 - Maximum Symbol Rate
- Result Codes
- Fax Class 1 and Fax Class 1.0 Commands
- Fax I/O Processing
- Commands and Parameters
- Mode Entry Commands
- Mode Commands
- Service Class 1 Parameters
- Examples
- Voice Commands
- Voice Commands Overview
- Voice Commands
- Configuration Commands
- Voice Commands
- +VIP - Voice Initialize All Parameters
- +VRX - Start Modem Receive (Record)
- +VTR - Start Voice Transmission and Reception (Voice Duplex)
- +VTS - Send Voice Tone(s)
- +VTX - Start Modem Transmit (Playback)
- +VGR - Voice Gain Receive (Record Gain)
- +VGT - Voice Gain Transmit (Playback Volume)
- +VIT - Voice Inactivity Timer (DTE/Modem)
- +VLS - Analog Source/Destination Selection
- +VRA - Ringback Goes Away Timer
- +VRN - Ringback Never Appeared Timer
- +VSD - Silence Detection (Quiet and Silence)
- +VSM - Compression Method Selection
- +VTD - Beep Tone Duration Timer
- +VDR - Distinctive Ring
- +VDT - Control Tone Cadence Reporting
- +VBT - Buffer Threshold Setting
- +VPR - Select DTE/Modem Interface Rate (Turn Off Autobaud)
- Speakerphone Commands