Document Outline

• VPD-X5501-EN.pdf
  • FCC Notice
  • Safety Instructions
  • Notes on the AC Power Cord
    • Introduction
      • Projector Features
      • Package Contents
    • Projector with Lens Cap
    • AC Power Cord
      • Projector Overview
    • Using the Product
      • Control Panel
      • Connection Ports
      • Remote Control
      • Installing the Batteries
        • 1. Open the battery cover in the direction shown.
        • 2. Install batteries as indicated by the diagram inside the compartment.
        • 3. Close the battery cover into position.
      • Remote Control Operation
    • Installation
      • Connecting the Projector
      • Powering On/Off the Projector
  • Powering On the Projector:
    • 1. Remove the projector lens cap.
    • 2. Complete the AC power cord and peripheral signal cable(s) connections.
    • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.
    • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
  • Powering Off the Projector:
    • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
    • 2. Press button again to confirm.
    • 3. Disconnect the AC power cord from the electrical outlet and the projector.
    • 4. Do not turn on the projector right after power off.
    • Adjusting the Projector
  • Adjusting the Projector Height
    • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
    • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
  • Adjusting the Projector Focus
    • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
  • Adjusting Projection Image Size
    • Menu Operation
      • 1. Press the MENU button to open the OSD menu.
      • 2. When OSD is displayed, use p / q to select any feature in the main menu.
      • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
      • 4. Use p / q to select the desired item and adjust the settings with t / u.
      • 5. Press the MENU button, the screen will return to the main menu.
      • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
    • Network Control
      • 1. Connect one end of the internet cable to the Network Control connector on the projector.
      • 2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.
      • 3. Turn on your projector and computer.
      • 1. Enable DHCP from the projector OSD, under Network Config.
      • 2. Start browser in PC and specify following URL, then click “Go” button.
      • 3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
      • 1. Set IP Address and Subnet Mask under Network Config.
      • 2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..
      • 3. Select "Intel Protocol (TCP/IP)" and click "Properties".
      • 4. Set your PC’s IP address, and click OK.
      • 5. Start browser in PC and specify following URL, then click “Go” button.
      • 6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
      • 1. Go to Tools > General and click "Settings".
      • 2. Click "Every visit to the page" and "OK".
      • 3. Click "OK" to exit "Internet Properties".
    • Maintenance
      • Cleaning the Lens
      • Cleaning the Projector Housing
      • Cleaning the Filter Cover
        • 1. Switch the projector off and unplug the AC power cord from the wall socket.
        • 2. Remove the filter cover as the illustration shown.
        • 3. Clean the filter cover.
        • 4. Replace the filter cover.
        • 5. Attach the filter cover.
        • 6. Plug the power back into the projector.
      • Replacing the Lamp
        • 1. Turn off the projector.
        • 2. If the projector is installed in a ceiling mount, remove it
        • 3. Unplug the power cord.
        • 4. Loosen the screw in the side of the lamp cover and remove the cover.
        • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
        • 6. Insert the new lamp module into the projector and tighten the screws.
        • 7. Replace the lamp cover and tighten the screw.
        • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
        • 9. Reset the lamp hour. Refer to the “Setting” menu.
    • Specifications
    • Appendix
      • LED Indicator Messages
      • Compatibility Modes
  • Computer:
  • Video:
    • Troubleshooting
  • Start-up problems
  • Image problems
    • RS-232 Command and Configuration
    • IR Control Code