Signamax 8-Port 10/100/1000 Compact Industrial Unmanaged Switch - Manual

Name LED Status Description
Off Power input 1/2 is not yet connected.
P1/P2 Green
On Power status is ready.
Off Link is broken, or no cable is connected.
Green
Blink Data is being transferred through the port.
Off The link is operating at a 10/100 Mbps rate.
RJ-45
Yellow
On The link is operating at a 1000 Mbps rate.
P2 P1
V+ V- V+ V- F.G.
Pin V+ V- F.G.
Signal DC9-48V 0V Frame Ground
9 0
.6
m
m
Industrial DIN-Rail Unmanaged
Gigabit Ethernet Switch
065-7408GTB
8-port Industrial Unmanaged Gigabit Ethernet Switch
Hardware Installation Guide
Version 1.0
Released April, 2011
Introduction
Thank you for purchasing the Signamax 065-7408GTB Industrial
Unmanaged Gigabit Ethernet Switch. This document intends to provide
customers with brief descriptions of the product and to assist our
customers to start to use this device.
Inside the Package
- Main Product
■ One Signamax 065-7408GTB Industrial Unmanaged Switch.
- Standard Accessories
■ Terminal block for power input
■ This hard copy of the Hardware Installation Guide
Product Description
065-7408GTB
8-Port Industrial Unmanaged Gigabit Ethernet Switch
■ 8 10/100/1000BaseT/TX ports with RJ-45 connector
■ 5-pin Terminal Block type power connector
■ 2 LEDs indicating Power1 (P1) and Power2 (P2) status
Hardware Installation
Step1: Installation on “Din-Rail”
■ The 065-7408GTB switch is equipped with a Din-Rail bracket
attached onto the rear panel. Please follow the steps below to
fasten the switch to the Din-Rail correctly.
■
Tip the switch forward and press it against the Din-Rail after
aligning the bracket springs to the Din-Rail.
■
Press the bracket against the upper ledge of the Din-Rail until it
clicks.
Please Note:
The switch is designed to be mounted on a well-grounded place,
such as a metal panel.
Step2: Connection to Power
■ Prepare a suitable power source (such as the Signamax DC-1824-30W
Hardened Power Supply) and connect it into the switch by
Terminal Blocks (TB5).
■ The 065-7408GTB can utilize power ranging from 9-48 Volts DC.
■ Two DC inputs can be connected to the switch’s power terminals if
redundant power backup is needed.
■ Check the P1/P2 power LED. The LED(s) will be illuminated when the
switch is ready for use.
Step3: Connecting the Network Devices
■ Connect your devices using standard UTP/STP cable with RJ-45
connectors to the switch. (For the cable wiring diagrams, please
refer to the Pin Assignment)
■ The corresponding RJ-45 LED will be lighted if the Ethernet
connection is linked successfully.
■ The LED will be blinked during data transfer by the switch.
※UL Notice for Power supplies
All the series of products are intended to be supplied by a Listed
Power Unit marked with “LPS”, “Limited Power Source” or “Class 2”
with output rate 9-48VDC, 0.45A maximum.
Or, use any of the following recommended power supply models from
Signamax:
• DC-1824-30W
• DC-1824-60W
• DC-1824-75W
• DC-1824-120W
• DC-1848-75W
• DC-1848-120W
LED Indicators
There are some LED indicators located at the front panel of the switch.
P2 P1
V+ V- V+ V- F.G.
P2 P1
7 8
5-pin Terminal Block for Power Input
5 6
3 4
Warning:
Before connecting the switch to the DC power input, please make sure
the DC voltage supplied by the power source is correct and stable.
1 2