Document Outline

• Introduction and Safety
  • Introduction
  • Safety
    • Safety terminology and symbols
    • Environmental safety
    • User safety
    • Ex-approved products
  • Product warranty
• Transportation and Storage
  • Inspect the delivery
    • Inspect the package
    • Inspect the unit
  • Transportation guidelines
    • Pump handling and lifting
  • Storage guidelines
    • Pump storage requirements
• Product Description
  • General description
    • Part description
  • Nameplate information
• Installation
  • Preinstallation
    • Pump location guidelines
    • Foundation requirements
  • Baseplate-mounting procedures
    • Prepare the baseplate for mounting
    • Install the baseplate using shims or wedges
  • Pump-to-driver alignment
    • Alignment checks
    • Permitted indicator values for alignment checks
    • Alignment measurement guidelines
    • Attach the dial indicators for alignment
    • Pump-to-driver alignment instructions
      • Perform angular alignment for a vertical correction
      • Perform angular alignment for a horizontal correction
      • Perform parallel alignment for a vertical correction
      • Perform parallel alignment for a horizontal correction
      • Perform complete alignment for a vertical correction
      • Perform complete alignment for a horizontal correction
  • Grout the baseplate
  • Piping checklists
    • General piping checklist
    • Suction-piping checklist
    • Discharge piping checklist
    • Final piping checklist
• Commissioning, Startup, Operation, and Shutdown
  • Preparation for startup
  • Remove the coupling guard
  • Check the rotation - Frame Mounted
  • Couple the pump and driver
    • Install the coupling guard
  • Pump priming
    • Prime the pump with the suction supply above the pump
    • Prime the pump with the suction supply below the pump
    • Other methods of priming the pump
  • Start the pump
  • Pump operation precautions
  • Shut down the pump
  • Make the final alignment of the pump and driver
• Maintenance
  • Maintenance schedule
  • Bearing maintenance
    • Ball bearing types
    • Grease lubrication schedule
    • Lubricating-grease requirements
    • Regrease the grease-lubricated bearings
    • Lubricate the bearings after a shutdown period
  • Shaft-seal maintenance
    • Mechanical-seal maintenance
  • Disassembly
    • Disassembly precautions
    • Tools required
    • Drain the pump
    • Prepare for disassembly
    • Disassemble the discharge end ball bearing for the radial suction configuration
    • Disassemble the pump body
    • Disassemble the suction end ball bearings
    • Remove the shaft seal
  • Preassembly inspections
    • Replacement guidelines
  • Reassembly
    • Prepare for reassembly
    • Reassemble the shaft seal
    • Reassemble the suction end ball bearings
    • Reassemble the pump body
    • Complete the reassembly for the end suction configuration
    • Reassemble the discharge end ball bearings for the radial suction configuration
  • Assembly references
    • Torque values
    • Gap widths
    • Nozzle loads
    • Recommended minimum flows
    • Wearing parts and dimensions
• Troubleshooting
  • Alignment troubleshooting
  • Operation troubleshooting
• Parts Listings and Cross-sectional Drawings
  • Recommended spare parts
  • Radial suction all-iron cross-sectional
  • Radial suction all iron with stainless steel impeller cross sectional
  • Radial suction stainless steel cross-sectional
  • End-suction all-iron cross-sectional
  • End-suction all-iron with stainless steel impeller cross-sectional
  • End-suction stainless steel cross-sectional
  • Radial suction (counterclockwise rotation) all-iron cross-sectional
  • Radial suction (counterclockwise rotation) all-iron with stainless steel impeller cross-sectional
  • Radial suction (counterclockwise rotation) stainless steel cross-sectional