Document Outline

• PCM-9586 Manual
• Contents
• Chapter 1 Introduction
  • 1.1 Introduction
  • 1.2 Features
  • 1.3 Specifications
  • 1.4 Board layout: dimensions
    • Figure 1.1: Board layout: dimensions (component side)
    • Figure 1.2: Board layout: dimensions (solder side)
• Chapter 2 Installation
  • 2.1 Jumpers
    • Table 2.1: Jumpers
    • 2.1.1 Jumpers setting drawing
  • 2.2 Connectors
    • Table 2.2: Connectors
  • 2.3 Locating jumpers and Connectors
    • Figure 2.1: Jumper & Connector (component side)
    • Figure 2.2: Jumper & Connector (solder side)
  • 2.4 Setting Jumpers
  • 2.5 Clear CMOS (JP3)
  • 2.6 Installing DIMMs
  • 2.7 IDE, CDROM hard drive connector (CN5, CN6)
    • 2.7.1 Connecting the hard drive
  • 2.8 Solid State Disk
    • 2.8.1 CompactFlash (CN20)
  • 2.9 Floppy drive connector (CN8)
    • 2.9.1 Connecting the floppy drive
  • 2.10 Parallel port connector (CN4)
  • 2.11 Keyboard and PS/2 mouse connector (CN19)
  • 2.12 Front Panel Connector (CN3)
    • 2.12.1 Power & HDD LED (pin 1-4 of CN3)
    • 2.12.2 Reset switch (pin 13-14 of CN3)
  • 2.13 Power connectors (CN10,CN15)
    • 2.13.1 ATX power connector, +5V (CN15)
    • 2.13.2 CPU Fan power supply connector (CN10)
  • 2.14 ATX power ON/OFF switch con. pin 11-12 of CN3
    • 2.14.1 ATX feature (CN15) & soft power switch (CN3)
  • 2.15 Audio AC'97 Link interfaces (CN14)
    • 2.15.1 Audio connector(CN14)
    • 2.15.2 CD audio-in connector (CN18)
  • 2.16 COM port connector (CN11)
  • 2.17 VGA/LVDS interface connections (CN13, CN16,CN7)
    • 2.17.1 CRT display connector (CN13)
    • 2.17.2 LVDS LCD panel connector (CN16)
    • 2.17.3 DVI LCD panel connector(CN7)
  • 2.18 TV-out interface (CN12)
  • 2.19 Ethernet configuration (CN2, CN23)
    • 2.19.1 100Base-T connector (CN23)
    • 2.19.2 Network boot
  • 2.20 USB connectors (CN25,CN26,CN27)
• Chapter 3 Software Configuration
  • 3.1 Introduction
  • 3.2 Connections to Three Standard LCDs
    • 3.2.1 LG LM150X06 (1024x768(16 colors) LVDS LCD)
  • 3.3 Installing the CSI Utility
• Chapter 4 Award BIOS Setup
  • 4.1 System test and initialization
    • 4.1.1 System configuration verification
  • 4.2 Award BIOS setup
    • 4.2.1 Entering setup
      • Figure 4.1: BIOS setup program initial screen
    • 4.2.2 Standard CMOS Features setup
      • Figure 4.2: CMOS Features setup
    • 4.2.3 Advanced BIOS Features setup
      • Figure 4.3: Advanced BIOS Features setup
    • 4.2.4 Advanced Chipset Features setup
      • Figure 4.4: Advanced Chipset Features setup
    • 4.2.5 Integrated Peripherals
      • Figure 4.5: Integrated Peripherals
    • 4.2.6 Power Management Setup
      • Figure 4.6: Power Management Setup
    • 4.2.7 PnP/PCI Configurations
      • Figure 4.7: PnP/PCI Configurations
    • 4.2.8 PC Health Status
    • 4.2.9 Frequency/Voltage Control
      • Figure 4.8: Frequency/Voltage Control
    • 4.2.10 Load Optimized Defaults
      • Figure 4.9: Load optimized Defaults
    • 4.2.11 Set Password
    • 4.2.12 Save & Exit Setup
      • Figure 4.10: Save & Exit Setup
    • 4.2.13 Exit Without Saving
      • Figure 4.11: Exit Without Saving
• Chapter 5 PCI Graphic Setup
  • 5.1 Introduction
    • 5.1.1 Chipset
    • 5.1.2 Display memory
    • 5.1.3 Display types
    • 5.1.4 Dual/Simultaneous Display
      • Figure 5.1: Selecting Display Settings
  • 5.2 Installation of the PCI Graphic driver
    • 5.2.1 Installation for Windows 98/ME/2000/XP
  • 5.3 Further Information
• Chapter 6 Audio Setup
  • 6.1 Introduction
  • 6.2 Driver installation
    • 6.2.1 Before you begin
• Chapter 7 PCI Bus Ethernet Interface
  • 7.1 Introduction
  • 7.2 Features
  • 7.3 Installation of Ethernet Driver
    • 7.3.1 Installation for Windows 98&2000
  • 7.4 Further information
• Appendix A Prog. GPIO & W’dog Timer
  • A.1 Supported GPIO Register
    • A.1.1 GPIO Registers
    • A.1.2 GPIO Example program-1
  • A.2 Watchdog programming
• Appendix B Pin Assignments
  • B.1 CPU fan connector (CN10)
  • B.2 Ethernet 10/100Base-T Connector (CN23)
  • B.3 Ethernet 10/100/1000 BASE-T connector (CN2)
  • B.4 Ethernet LED connector(CN1)
  • B.5 ACLink audio connector (CN14)
  • B.6 CD-IN Connector (CN18)
  • B.7 ATX Main Power Connector (CN15)
  • B.8 Keyboard and PS/2 Mouse Connector (CN19)
  • B.9 Floppy Disk Drive Connector (CN8)
  • B.10 IDE Hard Drive Connector (CN5, CN6)
  • B.11 Parallel Port Connector (CN4)
  • B.12 Front Panel LED (CN3)
  • B.13 USB Connector (CN25,26,27)
  • B.14 SIR Connector (CN24)
  • B.15 TV Out Connector (CN12)
  • B.16 LCD Inverter Backlight Connector (CN17)
  • B.17 CRT Display Connector (CN13)
  • B.18 LVDS Connector (CN16)
  • B.19 COM Port Connector (CN11)
  • B.20 CompactFlash Card Connector (CN20)
  • B.21 GPIO Connector (CN9)
  • B.22 TMDS Connector(CN7)
  • B.23 Mini PCI Connector
• Appendix C System Assignments
  • C.1 System I/O Ports
    • Table C.1: System I/O Ports
  • C.2 1st MB memory map
    • Table C.2: 1st MB memory map
  • C.3 DMA channel assignments
    • Table C.3: DMA channel assignments
  • C.4 Interrupt assignments
    • Table C.4: Interrupt assignments
• Appendix D Optional Extras
  • D.1 PCM-10586-6100 Cable kit for PCM-9581F/PCM- 9586F
    • Table D.1: PCM-10586-6100 wiring kit 9581F/9586F
  • D.2 Optional USB cable (CN25,26,27)
  • D.3 ATX Power Control Cable (CN15)
• Appendix E Mechanical Drawings
  • E.1 Mechanical Drawings
    • Figure E.1: PCM-9586 Mech Drawing (component side)
    • Figure E.2: PCM-9586 Mech Drawing (solder side)