Document Outline

• Contents
• About This Manual
• 1.0 Introduction
  • 1.1 System Configurations and Options
  • 1.2 Support Software
    • 1.2.1 Virtui2
    • 1.2.2 Revolution III
    • 1.2.3 iRev 4
    • 1.2.4 Supporting Indicators
    • 1.2.5 Communications Requirements
• 2.0 Installation
  • 2.1 Unpacking and Assembly
  • 2.2 Mounting the Enclosure
  • 2.3 Cable Connections
    • 2.3.1 Cable Grounding
  • 2.4 Load Cells
  • 2.5 Serial Communications
  • 2.6 Digital I/O
  • 2.7 Primary/Secondary Wiring and Configuration
    • 2.7.1 Assigning Board Addresses
    • 2.7.2 Restore System Defaults
  • 2.8 Installing Option Cards
  • 2.9 Transient Board
  • 2.10 Parts Kit Contents
  • 2.11 Replacement Parts and Assembly Drawings
• 3.0 Configuration
  • 3.1 920i Configuration
    • 3.1.1 Connecting with the 920i
    • 3.1.2 Manual Assignment with the 920i
    • 3.1.3 920i–iQUBE2 Menu Configuration
    • 3.1.4 Associating a Scale
  • 3.2 Virtui2 Configuration
    • 3.2.1 Starting and Logging in to the Virtui2 Configuration Utility
    • 3.2.2 Info
    • 3.2.3 Device Configuration
    • 3.2.4 Communications
    • 3.2.5 Load Cells
    • 3.2.6 Load Cell Assignment
    • 3.2.7 Scale Configuration
    • 3.2.8 Additional iQUBE2 System Configuration
    • 3.2.9 Print Formatting
    • 3.2.10 Sending Configuration to iQUBE2
  • 3.3 Revolution III Configuration
    • 3.3.1 Revolution III Configuration
    • 3.3.2 Downloading to the iQUBE2
• 4.0 Calibration
  • 4.1 920i Calibration
    • 4.1.1 Front Panel Calibration
    • 4.1.2 Advanced Calibration Options
  • 4.2 Virtui2 Configuration Utility Calibration
    • 4.2.1 2-Point Calibration
    • 4.2.2 Corner Match
    • 4.2.3 Section Match
    • 4.2.4 Theoretical Calibration
    • 4.2.5 Temporary Zero Calibration
  • 4.3 Revolution III Calibration
• 5.0 Serial Commands
• 6.0 Diagnostics
  • 6.1 Diagnostic Functions
    • 6.1.1 Diagnostic Error Detection
    • 6.1.2 Retrieving Diagnostic Data
  • 6.2 Diagnostic Commands
    • 6.2.1 System Diagnostic Commands
    • 6.2.2 Cell Diagnostic Commands
    • 6.2.3 Scale Diagnostic Commands
    • 6.2.4 Diagnostic Flag Commands
• 7.0 Data Formatting
  • 7.1 Weight Data Formats
    • 7.1.1 Data Format Tokens
    • 7.1.2 Weight Data Status Codes
    • 7.1.3 Diagnostic Codes
  • 7.2 Data Formatting Examples
    • 7.2.1 Formatting Data from Multiple Scales
    • 7.2.2 Using the Start/Stop Streaming Commands
    • 7.2.3 Encapsulating Data with Prefix and Postfix Characters
• 8.0 Appendix
  • 8.1 Digital Filtering
  • 8.2 Cell Emulation
    • 8.2.1 Section Match
    • 8.2.2 Corner Match
    • 8.2.3 2-Point
    • 8.2.4 Cell Emulation in Virtui2
    • 8.2.5 Cell Emulation in Revolution III
    • 8.2.6 Cell Emulation with a 920i Indicator
  • 8.3 Power Considerations
    • 8.3.1 System Current Draw
    • 8.3.2 System Voltage Drop
  • 8.4 Installing Firmware Updates
  • 8.5 Replacing CPU Boards
    • 8.5.1 Replacing the Primary CPU Board
    • 8.5.2 Replacing a Secondary CPU board
  • 8.6 Troubleshooting
    • 8.6.1 General Steps
  • 8.7 Printed Information
  • 8.8 Specifications
• iQUBE2 Limited Warranty