Document Outline

• About the UPS
• Safety
• Product Overview
  • Front panel
  • Rear panel
• Specifications
  • Operating Conditions
  • Environmental Specifications
• Installation
  • UPS
  • Network Management Card
  • External Battery Pack
• Connect Equipment to the UPS
  • 1 . Connect equipment to the outlets on the rear panel of the UPS. Do not use extension cords, pl...
  • 2 . Connect the UPS to the building utility power. Connect the UPS to a two-pole, three-wire, gro...
  • 3 . Press the On/Off button on the front panel of the UPS to apply power to the unit and all conn...
  • 4 . To use the UPS as a master on/off switch, turn on all the equipment that is connected to the ...
  • Basic Connections
• Display Interface
  • Overview
  • Using the display interface
  • Standard Menus
    • • Operating mode
    • • Controllable Outlet state, On or Off
    • • Efficiency of the UPS
    • • Information about the load
    • • Battery capacity
    • • Estimated runtime
    • • Input and output voltage and frequency
    • • Information about the last transfer to battery power
    • • Self-test results
    • • Language
    • • Local power quality: Good, Fair, Poor
    • • Choose Standard or Advanced menus
    • • LCD Display mode, Always On or Power-Saving
    • • Audible alarms
    • • Reset to Factory Defaults
    • • Unit model number
    • • Serial number
    • • Battery installation date
    • • Suggested battery replacement date
    • • Replacement Battery Cartridge model number
    • • UPS firmware version
  • Advanced Menus
    • • Energy meter
    • • Number of external battery packs connected to the UPS
    • • Load current
    • • Status of the Controllable Outlet Groups
    • • Battery voltage
    • • UPS and Controllable Outlet group delays and settings
    • • High and lower transfer points
    • • Sensitivity settings
    • • Date of last battery replacement
    • • Hardware version
    • • Software version
    • • NMC information (if applicable)
• UPS Settings
  • Start-up Settings
    • • English
    • • French*
    • • German*
    • • Spanish*
    • • Italian*
    • • Good
    • • Fair
    • • Poor
    • • If Good is selected, the unit will go on battery power more often to provide the cleanest power...
    • • If Poor is selected, the UPS will tolerate more fluctuations in power and will go on battery po...
  • General Settings
    • • Never
    • • Start-up only
    • • Frequency of test
• Controllable Outlet Groups
  • Overview
  • Model-specific Controllable Outlet Groups
    • 750VA, 120 V and 230 V
    • 1000 VA, 120 V and 230 V
    • 1500 VA, 120 V and 230 V
  • Using the Controllable Outlet Groups and UPS outlets
    • 1 . Connect critical equipment to the UPS outlets (except for 1500 VA models; then, connect all c...
    • 2 . Connect peripheral equipment to the Controllable Outlet Groups.
    • 3 . Use the Configuration menus to configure how the Controllable Outlet Groups will react in the...
  • Customize the Controllable Outlet Groups and the UPS outlets
    • • Shutdown with Delay
    • • Shutdown immediately
    • • Turn off immediately
    • • Turn off with delay
    • • Disabled
    • • Shutdown with delay
    • • Shutdown immediately
    • • Turn off immediately
    • • Turn off with delay
    • • Disabled
    • • Disabled
    • • Enabled
  • Network Management Card Settings
• Emergency Power Off
  • EPO Overview
  • Normally open contacts
    • 1 . If the EPO switch or relay contacts are normally open, insert the wires from the switch or co...
    • 2 . Secure the wires by tightening the screws.
  • Normally closed contacts
    • 1 . If the EPO switch or relay contacts are normally closed, insert the wires from the switch or ...
    • 2 . Insert a wire jumper between pins 1 and 2. Secure the wires by tightening the three screws at...
  • Service
    • 1 . Review the problems discussed in Troubleshooting in this manual to eliminate common problems.
    • 2 . If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com.
    • a. Note the model number of the UPS, the serial number located on the rear side of the unit, and ...
    • b. Call APC Customer Support and a technician will attempt to solve the problem over the phone. I...
    • c. If the UPS is under warranty, repairs are free.
    • d. Procedures for servicing or returning products may vary internationally. Refer to the APC Web ...
    • 3 . Pack the UPS in its original packaging. If this is not available, refer to www.apc.com for in...
    • a. Pack the UPS properly to avoid damage in transit. Never use foam beads for packaging. Damage s...
    • b. Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transporta...
    • 4 . Write the RMA# provided by Customer Support on the outside of the package.
    • 5 . Return the unit by insured, pre-paid carrier to the address given to you by Customer Support.
  • Transport the UPS
    • 1 . Shut down and disconnect all equipment connected to the UPS.
    • 2 . Shut down and disconnect the UPS from utility power.
    • 3 . Disconnect the UPS from all internal and external batteries.
    • 4 . Follow the shipping instructions outlined in the Service section of this manual.
  • APC Worldwide Customer Support
  • LIMITED WARRANTY
• © 2009 APC by Schneider Electric. APC, the APC logo are owned by Schneider Electric Industries S....