Document Outline

• 1. Introduction
  • 1.1. Overview
    • 1.1.1. Grain Transfer Boot and PTO Driveline
    • 1.1.2. Grain Hopper
    • 1.1.3. Auger Tube Hydraulic Lift
• 2. Safety
  • 2.1. General Safety Information
  • 2.2. Assembly Safety
  • 2.3. Operation Safety
  • 2.4. PTO Safety
  • 2.5. Hydraulic Safety
  • 2.6. Transport & Placement Safety
  • 2.7. Maintenance Safety
  • 2.8. Safety Decals
    • 2.8.1. Decal Installation/Replacement
    • 2.8.2. Safety Decal Locations
    • 2.8.3. Safety Decal Detail
• 3. Assembly
  • 3.1. General Assembly
  • 3.2. Assemble the Auger Tube
    • 3.2.1. Identify and Arrange Auger Tube Sections
    • 3.2.2. Connect Auger Tubes
    • 3.2.3. Install the Hydraulic Lift Cylinders
    • 3.2.4. Install the Track Shoe and Track Stop
    • 3.2.5. Install the Boot on the Auger Tube
    • 3.2.6. Assemble the PTO Shield Assembly
    • 3.2.7. Install the Speed Reducer on the Boot
    • 3.2.8. Install the Boot Tow Bar
    • 3.2.9. Install the Discharge Spout
    • 3.2.10. Set the Thrust Adjuster
    • 3.2.11. Apply Logo and Model Decals on the Auger Tubes
  • 3.3. Install Truss Support Towers and Truss Tubes
  • 3.4. Install Truss Cables
  • 3.5. Assemble the Lower Frame
  • 3.6. Assemble the Wheel Hub and Install Tires
  • 3.7. Connect the Auger Tube to the Frame
  • 3.8. Install Lift Cylinder Cables to the Track shoe
  • 3.9. Connect Hydraulic Hoses and Ball Valve
  • 3.10. Connect the PTO Driveline
  • 3.11. Connect the Intake Hopper to the Swing Tube
  • 3.12. Connect the Spout Head to the Grain Transfer Boot
  • 3.13. Install the Hopper Lift Arm
  • 3.14. Install the Hydraulic Winch
  • 3.15. Power Swing Assembly
    • 3.15.1. Connect the Lower Clamp to the Power Swing
    • 3.15.2. Connect the Wheels on the Power Swing
    • 3.15.3. Connect the Power Swing Wheel Assembly to the Tube
    • 3.15.4. Connecting the Power Swing Wiring
  • 3.16. Install the Hitch Jack
  • 3.17. Install the Manual Container
  • 3.18. Auger-to-Tractor Hookup
• 4. Transport
  • 4.1. Transport Position
• 5. Placement
  • 5.1. Placement Procedure
• 6. Operation
  • 6.1. Operator Controls
  • 6.2. Pre-Operation
    • 6.2.1. Checklist
    • 6.2.2. PTO Drive
    • 6.2.3. Hydraulics
    • 6.2.4. Electric Power Swing Operation
  • 6.3. Operating Procedures
    • 6.3.1. Initial Start-Up
    • 6.3.2. Normal Start
    • 6.3.3. Normal Shutdown
    • 6.3.4. Emergency Stop / Full-Tube Restart
    • 6.3.5. Lowering & Completion
    • 6.3.6. Operation in Reverse
• 7. Maintenance and Storage
  • 7.1. Maintenance Intervals
  • 7.2. Fluids and Lubricants
  • 7.3. Maintenance Procedures
    • 7.3.1. Visual Inspection
    • 7.3.2. Hydraulic Hose and Coupler Inspection
    • 7.3.3. Machine Greasing
    • 7.3.4. Hopper Lift Cable Inspection
    • 7.3.5. Winch and Pulley Servicing
    • 7.3.6. Gearbox Coupling Shaft Servicing
    • 7.3.7. Hopper Chain Drive Servicing
    • 7.3.8. Gearbox Oil Level
    • 7.3.9. Machine Cleaning
    • 7.3.10. Tire Pressure Check
    • 7.3.11. Wheel Bearings Repack
    • 7.3.12. Wheel Bolt Tightening
    • 7.3.13. Truss Cable Adjustment
    • 7.3.14. Changing Gearbox Oil
  • 7.4. Storage
  • 7.5. Power Swing
    • 7.5.1. Power Swing Maintenance
    • 7.5.2. Power Swing Storage
• 8. Troubleshooting
• 9. Appendix
  • 9.1. Specifications
  • 9.2. Bolt Torque Values
  • 9.3. Remote Transmitter Instructions
    • 9.3.1. Programming Receivers with Serial Numbers 293996 and Higher
  • Limited Warranty