Lightolier MULTISET PRO MDC20 - Manual (Page 6)

6
Changing the Fade Rate
MultiSet Pro® Dimmers can be programmed for 12 different fade rates. Dimmers
can be programmed to have a different fade rate on each scene.
The fade rate choices are:
1.5 seconds 1 minute
3 seconds 2 minutes
4.5 seconds 5 minutes
7.5 seconds 15 minutes
15 seconds 30 minutes
30 seconds 60 minutes
Global Fade Rate = One fade rate for all scenes.
Each dimmer’s fade rate affects all scenes. Examples: Dimmer #1 fade rate set 7.5 sec.,
dimmer #2 set to 15 sec., and dimmer #3 set to 3 sec. When any scene is selected dim-
mers #1, 2, and 3, will respond with 7.5, 15, and 3 seconds, respectively for ON, OFF,
A, B, C, D, E, F, G, H, I J, K, and L.
To change the Global Fade Rate that affects all scenes:
1. Tap the OFF button on the Master.
2. Press and hold the SET button. After 3 seconds, either a single green LED or a
pair of green LEDs indicates the current “global” fade rate. The bottom LED indi-
cates the 1.5 second fade rate, the next LED up is 3 seconds, while the top LED is
2 minutes. If the bottom two LEDs are on, it indicates the 5 minutes fade rate, if
the next two LEDs up are lit, it indicates 15 minutes, while the top two LEDs
indicate the 60 minute fade rate.
Note: When the two LEDs are on, they will not be at the same intensity.
3. While holding the Set button, tap the top of the rocker to sequence the LEDs
through the various fade rates until the desired fade rate is selected.
4. Release the SET button.
5. Repeat steps 2 - 4 for each device.
To change the fade rate that will affect only an individual scene:
1. Tap a scene button on the Master to go to a scene.
2. Press and hold the SET button.
3. After 3 seconds, either a single green LED or a pair of green LEDs indicates the
scene’s fade rate.
4. While holding the SET button, tap the top rocker until the desired fade rate is
reached.
5. Release the SET button.
6. Repeat above for each scene.
2 min
1 min
30 sec
15 sec
7.5 sec
4.5 sec
3 sec
1.5 sec
60 min
30 min
15 min
5 min
“Green”
LED Lights
M ULTI S ET P RO ® M ASTER (C LASSIC S ERIES )
• Tap the ON button to elegantly illuminate the entire area to the ON “preset”.
• Press and hold the ON button to brighten lighting level.
• Tap the OFF button to fade lights to OFF.
• Press and hold OFF button to lower lighting level.
• Tap a scene button to access “preset” light levels.
• Two quick taps of any button (including ON and OFF) will fade lighting quickly.
M ULTI S ET P RO ® M ASTER (E LLIPSE S ERIES )
• Press or Tap the ON button to elegantly illuminate the entire area to the ON “preset”.
• Press the RAISE button to brighten lighting level.
• Tap the OFF button to fade lights to OFF.
• Press LOWER button to lower lighting level.
• Tap a scene button to access one of the “preset” light levels.
• Two quick taps of any button (except RAISE or LOWER) will fade lighting quickly.
Figure 9
Figure 10
Operating Instructions
M
ULTI
S
ET
P
RO
® - P
RE
-W
IRED
D
IMMING
C
ABINET
MDC20 Installation
and Operation
Figure 12
Figure 11
Raise/Lower
Button
Built-in IR
Receiver
ON
OFF
A B
C D
Off
All-On
Classic Series
Ellipse Series
Step 1
Press and hold Set
button for 3 seconds.
Step 2
Tap top of dimmer paddle
to increment fade rate.
Step 3
Release Set button.