Linear 3022 - Manual (Page 2)

If you are going to use the 3022 transmitter in a safety
related device, be sure to read the manufacturer’s
instructions with regard to wiring and limitations of the
safety circuit.
After you have wired and coded the 3022, you are now
ready for mounting. You will note that there are four holes
in the case, through which you can mount your screws,
rivets, or other mounting devices. If the transmitter is to be
used in the proximity of metal, be sure to test the location at
the greatest distance the device will be from its receiver, in
order to be sure that adequate performance is achieved.
ANY METAL, INCLUDING MOUNTING PLATES, ETC., MAY
AFFECT THE PERFORMANCE OF YOUR TRANSMITTER.
Once you are satisfied with the performance of the radio,
you can permanently mount it.
Linear Corporation has taken every precaution to
assure that the 3022 will perform reliably. In order to
provide the greatest reliability, we have fastened the
printed circuit board to the case with a special fastening
agent, such as Loctite
 . We suggest that you use a similar
material to your fastening screws if vibration is likely to be
encountered.
…
IMPORTANT SAFETY TEST
…
Before releasing the radio transmitter for use, test the system for
proper operation after installing the radio transmitter and
associated hardware. The system should be tested at various
positions of travel of the gate member to be certain that the gate
edge, radio transmitter, receiver and gate operator are
functioning to detect an obstruction and reverse or stop the
gate.
MAINTENANCE
The 3022 Transmitter needs a minimum of care,
however, certain precautions must be taken:
1. Be sure to check the 3022 Transmitter as a system. Be
sure that the device that is connected to the 3022 is
f u nc t i on i ng w it h t h e t r a n s m i t t e r , a n d w i t h t h e
receiver.
2. Check the system to which the 3022 is attached fre-
quently.
3. The 3022 employs long life Alkaline-Manganese Dioxide
Batteries (Eveready Energizer 522 or equivalent). Nominal
life for these batteries is three years, but we suggest you
test the unit more often than this. Test the transmitter any
time you perform maintenance on the rest of the system.
WARRANTY
MULTI-CODE products products carry an eighteen (18) month
warranty against defects in workmanship or material. This
warranty begins at the date of manufacture, for eighteen
months. Linear Corporation warrantees our product only to
our authorized dealers and distributors, and not to the end
customer. If you have questions about our warranty, please
ask your dealer to determine the nature and scope of his
warranty. Linear Corporation does not assume, and is not
responsible for, any real or consequential damages from
claims against the performance of our product, nor is it
liable for any costs related to loss of life, property, or
revenue. Further, Linear Corporation is in no way
responsible for installation of our product, and will assume
n o c o s t s t o r e i n s t a l l a t i o n o r r e m o v a l . L i n e a r
Corporation’s Warranty is in lieu of all other warrantees, ex-
pressed, or implied.
PLEASE NOTE
Linear Corporation has devoted a great deal of time and
research in order to provide the most reliable equipment
possible. Certain limitations must be observed.
1. MULTI-CODE radio components must conform with
FCC Part 15 requirements. For this reason, the range
and power of our radios is within specified limits.
2. As with all manufacturers, MULTI-CODE radios
must accept all signals that they receive. This may, in
rare instances, create difficulty.
INSTR,
INSTL
,MC302
2,G
ATE XMTR
LI
NEAR
P/N:
214804 A
INK
: BL
ACK
MATERIAL: 2
0
LB. MEAD BOND
SI
ZE:
7.500"
x 7.500"
S
C
ALE: 1-1
SI
DE 2 OF
2
TERMINAL BLOCK
MTG. HOLE
BATTERY
MTG. HOLE MTG. HOLE
MTG. HOLE
CODE SWITCH
STRAIN RELIEF