Teka AUTOMATIC DRUM WASHING MACHINE LSE-1200 S - Manual (Page 10)

Control Panel
Control Panel (LSE-1200 S)
A Program knob
By turning this knob, it is possible to select the desired program
Refer to "Program Guide" to select the Program .The program
selector knob is at the same time a power swith; when the knob is
at " ", the washing machine is off; when the knob is in the other 11
positions, the washing machine is on.
B Temperature button
By pressing and holding down this button, it is possible to select the desired washing temperature ( ,
30, 40 60, 90C). Refer to "Program Guide" to Select the maximum temperature of each program.
When seledcted, the temperature is displayed in the digital display area on the screen.
Caution: Cold wash is selected when the symbol " " is displayed in the temperature display area .
C Speed button
By pressing and holding down this button, it is possible to select the desired spin speed (0, 400,
600, 800, MAX). Refer to the “Program Guide” to choose the maximum speed of each program.
When selected, the speed value is displayed inthe digital display area of the
screen.
Caution: the washing machine does not spin when the number “0” is displayed in the speed
display area of the screen. The washing machine spins at 1200 rpm when “MAX” is displayed in
the speed display area of the screen.
D Start / Pause button
When the electric cable of the washing machine is plugged in and a program is selected, after
the washing temperature, spinning speed and other required functions are set, lightly press
this button, operation will start. During a wash cycle, press this buttonlightly, operation will
pause. Press it again to resume operation.
Note: After operation is suspended, the washing temperature, spinning speed and other functions
can be reset. After that, press the Start/Pause button to continue operation.
E Economic
Press the key and manually select different programs and power-saving and water-seaving fea-
ture based on the volume of load.
29
Illistration of the washing operation process with "cotton" as an
example (The other processes resemble with this)
1.Joint the intake pipe and the drain pipe,switch the program button
to the position of closedown indication,and plug in the pin.
2.Open the door of the washing machine,trim up the cotton clothing that require
washing and put them into the cylindrical washer evenly.
3.Draw out the detergent dispensing package,put proper amount of detergent into the case2.If it is
needed to be softened,proper amount of liquid soften erorpliancy agent can be poured into the
softening room3.Notice that the volume should not above the position of “MAX” on the stopper
of the softening case.Then close the dispensing package.If the clothing are sodirty that need
pre-washing,proper amount of detergent can be put into case1 at the same time.
4.Choosing the washing temperature,rotation rate of dehydration and additional function.
If the heating temperature needs to be adjusted,you can press the temperature-choosing
button before start-up and choose proper heating temperature. The currently set temperature
will be presented in the digital display area and temperature display area of the display screen.
If the rotation rate of dehydration need stobe adjusted,you can press the rate-choosing button
before start-up and choose rotation rate of dehydration.Thecurrently setrotation rate of dehydration
will be presented in the digital display area and temperature display area of the display screen.
you can select the button of the automatic catch manually,and will be presented on the
digital display area of the display screen.If the button is being pressed with in 2 seconds you can
choose a proper code of clothing weight from to cyclically,the currently set clothing
weight will be presented in the digital display area,if any other codes or buttons will not be
chosen with in 5 seconds,the currently set clothing weight will be carried on.
If you need the drying function you can press the drying button and the icon of drying will be
lighted on the display screen.
If you need the ultra-clean rinsing function you can press the ultra-clean rinsing button and the
icon of ultra-clean rinsing will be lighted on the display screen.
If you need the prewashing function you can press the prewashing button and the icon of
prewashing will be lighted on the display screen.
If you need to set the washing time previously,you can press the reservation button,the
pre-engaging state of will be lighted in the digital display area of the display screen.Every
pressing of the reservation button will increase there servation time by 30 minutes(0—24hours).
If the reservation time is 4 hours, will be presented on the display screen,according to the
above set time 1:34,and 2 hours and 26 minutes later the program will start up,and finish it 4 hours later.
5.Press the Start/Pause button to start the washing process,meanwhile the left time will be
presented in the digital display area(there are towspots in the middle of the left time glittering),
the current heating temperature will be presented on the heating indication stripa ccordingly.30
seconds later the locking icon on the display screen will glitter which indicates that the door has
been locked and the program will be carry on.
6.When in the process of heating,the locking icon on the display screen will extinguish,the door
will be unlocked and can be opened at any time.When the inner temperature of the roller
reaches 55or above the door will be locked to prevent accidental scald when opening the
door.When the inner temperature of the roller is below 55the door will be unlocked.
7. will be presented on the display screen when the program is over,after a short noticing sound
the locking icon will extinguish indicates that the washing process is finished.Now you can switch
the program button to the position of close down,open the door,take put the clothing,and atlastd
is connect the water and electricity power.The laundry operation process is finished.Prompt:the
rate,temperature and function key scan be reselected and reset during some phases of the
processing of the program.
Notice:1.When the program has been started up,please don’t switch the program button as best
as you can,lest it will impact the processing program.You can also press down the
program knob.2.The left time on the display screen is just for reference,because of the
factors such as the temperature of the intake water,the heating temperature and the
equilibrium condition of the clothing when is being dehydrated,it is normal phenomenath
at the presented left time has been adjusted(increased or decreased)during some of the
washing processes.
Laundry Operation Illustration