Asus GigaX2024X User Manual
Gigax series, Layer 2 managed switch user guide
Advertising
Table of contents
Document Outline
- ASUSTeK COMPUTER INC. (Asia-Pacific)
- Technical Support
- ASUS COMPUTER INTERNATIONAL (America)
- ASUS COMPUTER GmbH (Germany and Austria)
- 1 Introduction
- 2 Getting to know the GigaX 2024X
- 3 Quick start guide
- 4 Management with the Web Interface
- 5 Console Interface
- 5.1 Power On Self Test
- 5.2 Login and Logout
- 5.3 CLI Commands
- 5.3.1 System Commands
- 5.3.2 Physical Interface Commands
- 5.3.3 Bridge Commands
- [Spanning Tree is] [STP Enabled/ RSTP Enabled/ Disabled]
- [Hello Time] [Forward Delay] [Max Age] [Bridge Priority]
- [Reload]
- [Show Trunk]
- [Create Trunk]
- [Add/Remove Trunk]
- [LACP Action]
- [LACP System Priority]
- CLI command : l2 trunk lacp syspri <priority (1-65535)>
- [LACP Port Priority]
- CLI command : l2 port lacppri <priority> <port list / * for all ports>
- [Reload]
- [Mirror Mode] [Enable/Disable]
- [Monitor Port] [port number]
- [Reload]
- [Show Multicast Group]
- [Remove Multicast Group]
- [Reload]
- [IGMP is] [Enabled/Disabled]
- [Reload]
- [Action] [Enable/Disable]
- [Mode] [Broadcast] or [Broadcast/Multicast] or [Broadcast/Multicast/Unknown unicast]
- [Limit Rate]
- [Reload]
- [Aging Time]
- [Query by Port]
- [Query by VLAN ID]
- [Query by MAC Address]
- [MAC Address]
- [VLAN ID]
- [Port Selection]
- [Reload]
- [Show VLAN]
- [Name]
- [VLAN ID]
- [Remove VLAN]
- [Reload]
- [Show Port]
- [PVID]
- CLI command : l2 port vlan <vlan id, 4095 to disable the port-based vlan> <port list>
- [CoS Value]
- [Reload]
- [CoS] [Map]
- [Scheduling Algorithm] [Strict/WRR]
- [Reload]
- 5.3.4 SNMP
- [Community Name] [Set]
- [Reload]
- [Host IP Address] [Community]
- [Reload]
- [Trap Version] [v1/v2c]
- [Destination]
- [Community for Trap]
- [Reload]
- [Group Name]
- [Read View Name]
- [Write View Name]
- [Notify View Name]
- [Security Model]
- [Security level]
- [Reload]
- [View Name]
- [View Type]
- [View Subtree]
- [View Mask]
- [Reload]
- [Engine Id]
- [Name]
- [Auth Protocol]
- [Auth Password]
- [Priv Protocol]
- [Priv Password]
- [Reload]
- 5.3.5 Security Commands
- [Reauthentication]
- [Reauthentication Time]
- [Authentication Method]
- [Quiet Period]
- [Retransmission Time]
- [Max Reauthentication Attempts]
- [Multi-host]
- [Authentication Control]
- [Reload]
- Allows user to modify a user entry from the local database. It contains a user name, password and dynamic VLAN.
- [Reload]
- [Reload]
- [Generate SSH key]
- [Reset SSH key]
- [Show Generating Status]
- 6 IP Addresses, Network Masks, and Subnets
- 7 Troubleshooting
- 8 Glossary