Asus P8H61-M2/TPM/SI R2.0 - Manual (Page 24)

ASUS P8H61-M2/TPM/SI R2.0 1-14
1.7.2 Memory configurations
You may install 1GB, 2GB, 4GB, and 8GB unbuffered non-ECC DDR3 DIMMs into the DIMM
sockets.
• You may install varying memory sizes in Channel A and Channel B. The system maps
the total size of the lower-sized channel for the dual-channel configuration. Any excess
memory from the higher-sized channel is then mapped for single-channel operation.
• Always install DIMMs with the same CAS latency. For optimal compatibility, we
recommend that you install memory modules of the same version or date code (D/C)
from the same vendor. Check with the retailer to get the correct memory modules.
• Memory module with memory frequency higher than 2133 MHz and its corresponding
timing or the loaded XMP Profile is not the JEDEC memory standard. The stability and
compatibility of these memory modules depend on the CPU's capabilities and other
installed devices.
• Due to the memory address limitation on 32-bit Windows ® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows ® OS.
- Install a 64-bit Windows ® OS when you want to install 4GB or more on the
motherboard.
• This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less..
P8H61-M2/TPM/SI R2.0 Motherboard Qualified Vendors Lists (QVL)
DDR3-2400 (O.C.) MHz capability
• The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency
adjustment.
• For system stability, use a more efficient memory cooling system to support a full
memory load (4 DIMMs) or overclocking condition.
Vendors Part No. Size
SS/
DS
Chip
Brand
Chip
NO. Timing
Voltage DIMM socket support (Optional)
1 DIMM 2 DIMMs 4 DIMMs
Corsair CMGTX8(XMP) 8GB (2GB x 4) SS - - 10-12-10-27 1.65V • • •
G.SKILL F3-19200CL11Q-16GBZHD(XMP1.3) 16GB(4GB x 4) DS - - 11-11-11-31 1.65V • •
G.SKILL F3-19200CL9D-4GBPIS(XMP) 4GB(2 x 2GB) DS - - 9-11-9-28 1.65V • •
GEIL GET34GB2400C9DC(XMP) 2GB DS - - 9-11-9-27 1.65V • •
Kingmax FLLE88F-C8KKAA HAIS(XMP) 2GB SS - - 10-11-10-30 1.8V • • •
Transcend TX2400KLU-4GK(427652)(XMP) 4GB(2 x 2GB) SS - - - 1.65V • • •
Transcend TX2400KLU-4GK (381850)(XMP) 4GB(2 x 2GB) SS - - 9 1.65V • • •
Transcend TX2400KLU-4GK(374243)(XMP) 4GB(2 x 2GB) DS - - 9 1.65V • •
PATRIOT PVV34G2400C9K(XMP) 4GB(2 x 2GB) DS - - 9-11-9-27 1.65V • •
• DDR3 1600 MHz and higher memory frequency is supported by Intel ® 3rd generation
processors.
• Due to Intel ® 2nd generation processors’ behavior, DDR3 2250 MHz and higher memory
frequencies runs at DDR3 2200 MHz as default. In addition, DDR3 2133 MHz runs at
2000 MHz and DDR3 1866 MHz runs at 1800 MHz as default.