Anthro Fit Standard Unit 24/30/36/48 Assembly Instructions - Manual

R
01–Worksurface ............................... Qty. 1 ....................... (see below)
24” Wide Worksurface (F24029zz/xx3) ............100-6527-00
30” Wide Worksurface (F3029zz/xx3) ...............100-6432-00
36” Wide Worksurface (F3629zz/xx3) ...............100-6433-00
48” Wide Worksurface (F4829zz/xx3) ...............100-6417-00
02– Support Bracket-B .................... Qty. 1 ...................225-2296-00
fi t Small Support Y fi t fi t (F2429zz/xx3) .. Qty. 1 ...................225-2015-00
03– 22.875” Vertical Legs .................Qty. 4 ...................125-5213-00
04– Base Tubes .......................................Qty. 2 ..................125-5273-00
05– Cross Tubes ................................ Qty. 2 ....................... (see below)
24” Deep Base Tube (F2429zz/xx3) ....................125-5218-00
30” Deep Base Tube (F3029zz/xx3) ....................125-5219-00
36” Deep Base Tube F3629zz/xx3) ......................125-5220-00
48” Deep Base Tube (F4829zz/xx3) ....................125-5214-00
06– Insert Screws ............................. Qty. 4 ...................325-5052-00
07– 2” Large End Caps .................... Qty. 4 ...................175-5157-00
08– 3” Locking Casters ................... Qty. 2 ...................150-5053-00
09– Caster Inserts ............................ Qty. 4 ...................525-5032-00
Component list for part #’s
F2429zz/xx3, F3029zz/xx3,
F3629zz/xx3 & F4829zz/xx3
10– 5 /
16
-18 fi t Bolts .......................... ...................325-5194-00
11– fi t Tube Washers ....................... Qty. 8 .. 225-2050-00 or 225-3522-00
12– 3” Non-Locking Casters ......... Qty. 2 ...................150-5052-00
13–
3 /
4
” Wood Screws ...................... Qty. 8 ...................325-5106-00
14– Support Bracket-A .................... Qty. 1 ................. 225-2295 -00
fi t Small Support X fi t fi t (F2429zz/xx3) .. Qty. 1 ...................225-2014-00
15– Support Screws ......................... Qty. 8 ...................325-5010-00
16– 1.5” Small Caps ......................... Qty. 4 ...................175-5156-00
17– Back Trough ................................ Qty. 1 ....................... (see below)
24” Wide Back Trough (F2429zz/xx3) ................225-2289-00
30” Wide Back Trough (F3029zz/xx3) ................225-2290-00
36” Wide Back Trough (F3629zz/xx3) ................225-2291-00
48” Wide Back Trough (F4829zz/xx3) ................225-2292-00
18– 1 /
4
-20 Button Head Screws .... Qty. 4 ...................325-5003-00
All Screw quantities listed here are the minimum needed
for your Standard Unit assembly. There may be a few extra
Screws included, which are not counted in the Parts List.
Anthro Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS! Rev. D January 2006
Step 8
Align the Base Assembly on the Vertical Tubes as shown.
Secure the Base Assembly by inserting a fi t Bolt through a
Tube Washer. Then insert the Bolt through the Base Tube
and carefully thread it into the Vertical Tubes.
Repeat for the remaining three Bolts and tighten all Bolts.
Step 9
Insert the four 1.5” Small End Caps into the Vertical Legs.
Congratulations! Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale fl yers.
Thank you for choosing Anthro!
Hello! Thank you for choosing Anthro.
Before beginning assembly of your Standard
Unit, please take a moment to review the
parts listed below to verify that your
shipment is complete.
Please review the assembly instructions
of all Anthro products you purchased and
are planning to include in this installation,
prior to beginning this assembly.
To make the assembly of your Standard
Unit even easier, we have included all of
the required tools. The handy Hex Driver
Bit can be used in your electric drill in place
of the Hex Driver.
Hex Driver 5 /
32
” ......... 375-5000-00
Hex Driver Bit 5 /
32
” .... 375-5003-00
8 oz. Rubber Mallet .... 375-5022-00
Questions? 1-800-325-3841
1.5” Small End Cap
( 5 /
16
-18 X 3.5”) fi t Bolt
325-5194-00
fi t Tube Washer
225-2050-00 or 225-3522-00
04
06
07
05
01
13
14
18
fi t Bolt fi t Bolt
fi t Tube
Washer
Cross Tube
24”/30”/36”/48” wide Standard Unit
Assembly Instructions
1-800-325-3841
NOTE: Detailed views of all Hardware are
provided with each Assembly Step.
Step 7
Attach a Cross Tube to a Base Tube by inserting a fi t Bolt
through a Tube Washer, then insert the Bolt through the
Base Tube and carefully thread into the Cross Tube.
Repeat this procedure for other Cross Tube. Then tighten
all fi t Bolts.
fi t Tube Washer
225-2050-00 or 225-3522-00
Cross Tube
fi t Tube
Washer
( 5 /
16
-18 X 3.5”) fi t Bolt
325-5194-00
fi t Bolt
Base Assembly