Jesel INS-35500 Donovan / Brodix +.400 Raised Cam - Manual (Page 4)

1985 CEDAR BRIDGE AVE.
LAKEWOOD, NJ 08701
732-901-1800, FAX 732-901-6777
www.jesel.com
THESE INSTRUCTION SHEETS ARE INTENDED AS REPRESENTATIONS ONLY. JESEL IS IN NO EVENT LIABLE FOR CONSEQUENTIAL DAMAGE,
INSTALLATION COST OR OTHER COST OF ANY NATURE. NO REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR JESEL ANY OTHER LIABILITY
IN CONNECTION WITH ANY JESEL PRODUCT. NOT RESPONSIBLE FOR TYPOGRAPHICAL ERRORS.
RECOMMENDED JESEL
BELT DRIVE MAINTENANCE:
CAM TIMING ADJUSTMENTS:
LOOSEN FOUR NUTS ON THE SPIDER. TURN THE
CRANKSHAFT CLOCKWISE TO RETARD THE CAM-
SHAFT TIMING AND COUNTER-CLOCKWISE TO
ADVANCE THE CAMSHAFT TIMING. EACH MARK
ON THE SPIDER GEAR EQUALS TWO DEGREES AT
THE CRANKSHAFT.
CAM ADAPTOR BOLTS - 28-30 FT / LBS
UPPER PULLEY NUTS - 20-25 FT / LBS
CAM SEAL THRUST PLATE NUT - 12 FT / LBS
7/16-20 LEFT HAND CAM BOLT - 70 FT / LBS
TORQUE SPECS:
KIT CONTENTS:
JESEL ALSO OFFERS A DISTRIBUTOR DRIVE KIT
FOR THIS BELT DRIVE . THE DISTRIBUTOR DRIVE
KIT ELIMINATES INACCURATE IGNITION TIMING
SETTINGS DUE TO CAMSHAFT TORSIONAL TWIST-
ING ON HIGH RPM ENGINES WITH EXCESSIVE
SPRING PRESSURES. IT ALSO PROVIDES A MUCH
COOLER LOCATION FOR THE DISTRIBUTOR. IN-
TAKE MANIFOLD CHANGES WILL BE MUCH EASIER
AS WELL THANKS TO THE DISTRIBUTOR NOT HAV-
ING TO BE ROUTED THROUGH THE REAR PORTION
OF THE INTAKE MANIFOLD. THIS KIT IS A DIRECT
BOLT ON.
KDD-42510, +.400 RAISED CAM
DISTRIBUTOR DRIVE KIT
KBD-42510 DISTRIBUTOR DRIVE
A
B
C
D
E
F
G
H
I
J
K
L
M
1) REPLACE BELT ANNUALLY OR AFTER ANY TYPE OF
ENGINE DAMAGE.
BEL-31060, TIMING BELT
2) REPLACE BOTH SEALS AND THRUST WASHERS
ANNUALLY.
SEL-38000 , CAMSHAFT SEAL
SEL-37300 , CRANKSHAFT SEAL
WSH-39610 , BRONZE THRUST WASHER, FRONT
WSH-39660 , BRONZE THRUST WASHER, REAR
3) COVER BELT DRIVE SYSTEM IF OPERATED ON
ABRASIVE TRACK SURFACES SUCH AS DIRT OR
SAND.
4) KEEP OIL OFF OF ALL SEALING SURFACES PRIOR
TO INITIAL START UP.
5) ALWAYS DEGREE AND RE-DEGREE CAMSHAFT AF-
TER TIMING BELT REPLACEMENT OR REMOVAL.
6) DO NOT CLEAN TIMING BELT WITH PARTS CLEAN-
ERS OR ENGINE DEGREASERS.
7) IF TIMING BELT BECOMES CONTAMINATED WITH
ENGINE OIL REPLACE IMMEDIATELY.
A) CVR-32550, BELT DRIVE COVER
B) SPD-38660, SPIDER
C) PLY-35520, CAMSHAFT PULLEY
D) PLY-35530, CRANKSHAFT PULLEY
E) BEL-31060, TIMING BELT
F) PLT-35260, THRUST PLATE WITH SEAL
G) ADP-30080, CAM ADAPTER
H) WSH-39750, CAM ADAPTER WASHER
L) DCL-32787, JESEL BELT DRIVE DECALS
M) KTB-38010, THRUST PLATE SHIMS
AVAILABLE TOOLS
I) TOL-39310, LOWER PULLEY DRIVER
J) TOL-39260, SPANNER WRENCH
K) TOL-19210, T45 TORX SOCKET
REQUIRES CRANK TRIGGER IGNITION SYSTEM
REV 04/08