Lokar Blower Drive Kickdown Cable - Manual

© 2012 Lokar, Inc.
INS0124
Rev. 05/23/12 Page 1
Building American Quality… With A Lifetime Warranty!
10924 Murdock Dr. • Knoxville, TN 37932
TOLL FREE 1-877-469-7440 • (865) 966-2269 • FAX (865) 671-1999 • [email protected] • www.lokar.com
®
Blower Drive Kickdown Cable Installation Instructions
Blower Drive Kickdown Cable Installation Instructions
For TH200, TH350, TH700-R4, TH200-4R, and 4L60
For TH200, TH350, TH700-R4, TH200-4R, and 4L60
General Installation Notes:
Please read instructions completely before beginning installation. If you
have any questions, please do not hesitate to call.
Do not attempt to install or adjust Kickdown Cable while engine is running.
Be sure engine, body and frame are grounded properly.
We recommend using an anti-seize lubricant on all aluminum threads
before installation. Do not over tighten while installing cables.
NOTE: Lokar’s Blower Drive Kickdown Cable Kits are designed to operate
with a Lokar Throttle Cable and BDS, Enderle or Weiand style linkage
for sideways mounted carburetors.
Step 1: Install and adjust all blower drive linkage components before
beginning to install the Lokar Blower Drive Kickdown Cable.
If a Lokar Blower Drive Throttle Cable has not previously been
installed and is being installed at the same time as the blower
drive kickdown cable, you must install the blower cable bracket
(see Lokar Blower Drive Throttle Cable Installation Instructions)
before beginning the blower drive kickdown cable installation.
Step 2: At the engine end of the blower drive kickdown cable, remove the
cable end stop. Slide the kickdown throttle body fitting, kickdown
mounting bracket and kickdown cable adjuster off of the inner wire.
Pull the inner wire out of the cable housing. Fig. 1
Step 3: From the engine end of the blower drive kickdown cable housing,
install the tube hold down clip onto the cable housing with the lip
pointed downwards, and slide it down to the trans tube at the end of
the cable housing. Temporarily install cable housing into transmis-
sion without the o-ring(s) and inner wire. Loosely install the bolt for
the tube hold down clip, to keep the cable housing from acciden-
tally coming out of the transmission. Fig. 2
Note: TH200 and TH350 transmissions could have come with either
a standard or a metric bolt for the trans tube hold down clip. For
those applications, we have included both a standard 1/4"-20 and
a metric M6 bolt and lock washer for the trans tube hold down clip.
The standard 1/4" – 20 bolt has a rounded button head, and the
metric M6 bolt has a square-shouldered socket head. The TH200-
4R, TH700-R4, and 4L60 will only have a metric bolt and washer
in the kit. Fig. 3
Step 4: The throttle cable adjuster goes through both the blower cable
bracket and the kickdown cable mounting bracket. If a Lokar throttle
cable has already been installed, disconnect the throttle cable inner
wire and remove the front throttle cable adjuster nut. If the throttle
cable is being installed at the same time as the kickdown cable,
insert the throttle cable adjuster into the blower cable bracket.
Cable End
Stop
Nylock
Jam Nut
Kickdown
Throttle Body
Fitting
Kickdown Cable
Adjuster
Kickdown Mounting Bracket
Inner Wire
Cable
Housing
Hex Carb
Fitting
Adjuster
Nuts
Ferrule
Kickdown Rod
Cable End will vary
by application
Tube Hold Down Clip
O-Ring Groove(s) -
TH350 & TH200
Shown, There are Two
O-Rings on TH200-4R,
TH700-R4, and 4L60
Trans Tube
Trans Tube Hold
Down Clip
1/4"-20 Standard
Button Head Bolt
and Lock Washer M6 Metric Socket
Head Bolt and
Lock Washer
Fig. 2
Fig. 3
Fig. 1