Mountain Off Road 8795-50 - Manual (Page 2)

This “kit” fits 1987-1995 Jeep® YJ Wrangler vehicles. It consists of the front bracket parts (un-welded) and hard-
ware to install them. Before starting installation, check the frame to make sure it is in good condition, is straight
and has no heavy rust. Only install it on vehicles in good sound condition. This kit will work with stock or most af-
termarket front bumpers, with or without a winch.
SHACKLES: This “kit” does not provide any means of attaching the shackles to the frame of the Jeep®. We as-
sume that you knew that when you ordered this part number. There are several different ways of attaching them
and you must know the proper methods and angles to make this S.R.S.™ function properly.
LEAF SPRINGS: This “kit” has been designed to work with stock (no lift) and aftermarket (lift) leaf springs. It will
work with the springs under the axle (stock), or, spring over axle (S.O.A.) set-up (custom).
PITMAN ARM: You may need to use a stock pitman arm. If a aftermarket pitman arm is used , the tie rod may
contact it upon suspension compression. Check for interference before driving !
DRIVE SHAFT: The front drive shaft may need to have a longer slip-yoke installed. Due to the action of the sus-
pension movement the stock slip-yoke may not have enough length or movement. We recommend calling the fol-
lowing drive line shop: Tom Wood’s Custom Drive Shafts, 1-877-497-4238 (toll free).
BRAKE HOSES: The stock brake hoses will work if you are using stock leaf springs under the axle. If you have
any lift in your springs, or a S.O.A. conversion, the stock brake hoses will have to be replaced with longer units.
M.O.R.E.™ recommends using Skyjacker® Suspension brand of brake hoses.
TRAC BAR and ANTI SWAY BAR: It is mandatory that you keep the trac bar and anti-sway bar in place when
using this shackle reversal system. If you desire full suspension articulation, M.O.R.E.™ suggests that you install
a pair of Quick Disconnects on the anti-sway bar and use our SlipLoc™ Trac Bar. These items are in our catalog.
FIT and TOLERANCES: All parts in this kit are the results of countless hours of research, testing, fitting and refin-
ing. Jeep® frames have a wide tolerance on bolt hole centers from frame to frame. This is why M.O.R.E.™ has
installed several “slots” in which to mount our bracketry. In addition to the factory tolerances, most people install
other then factory equipment such as bumpers, springs etc. M.O.R.E.™ has done the best job we can to insure
that our parts fit with all of the possibilities. However, you may find it necessary to grind, elongate, bend, or force
the parts in this “kit” to fit on your rig. Please use common sense when installing these parts.
TERMS-POLICIES:
DAMAGE CLAIMS: All orders are carefully packed, however, mishandling by the carrier can result in damage. The carrier has the responsibility
for the shipment from the time it leaves our warehouse until it is delivered to you. All claims for lost or damaged goods should be reported to the
carrier, not to M.O.R.E.™ LLC.
RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. After you receive a Return Goods Authorization (RGA)
number, merchandise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original
invoice or a copy with the RGA number written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for
credit or refund unless merchandise is proven to be defective or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit
or refund if it has been installed, modified, used in any way or is in unsalable condition.
WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper
use will void this warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee
the performance of any items. M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite
variety of conditions due to the manner in which they are used, serviced and/or installed. Purchasers and users of such products rely upon their
own judgment as to the suitable use selection, service and installation of such products.
PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous
condition which could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All
parts sold by M.O.R.E.™ LLC. are for racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal
injury or property damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.
Specifications are subject to change without notice.
Jeep®, AMC®, CJ®,YJ®, TJ®, Wrangler®, are registered trademarks of the DaimlerChrysler. M.O.R.E.™ is not associated with DaimlerChry-
ler.
M.0.R.E™, BombProof™, S.R.S.™, SlipLoc™, DoubleJointed™, RockProof™, are trademarks used by Mountain Off Road Enterprises,
LLC. The M.O.R.E.™ logo and this instruction sheet is copyright©, 2000-2008.
PAGE 2 of 5