Qmark SSHO Smart Series - High Out-Put Digital Wall Heater - Manual (Page 5)

2. Set Day and Time:
NOTE: For the following setup procedures, the display will auto-
matically save the setting after a 30 second pause and return to
the previous operating setting. If this occurs, start back at
Step a of the Set Day and Time procedure.
a. Simultaneously touch and hold the UP button and DOWN
button for 1.5 seconds. A beep will sound and the Day indi-
cator at the top of the display will flash (the buttons on the
display respond to touch, not pressure).
NOTE: If user touches the POWER button at any point during
setup procedure, the display will automatically save settings and
return to the previous operating setting.
b. Using the UP or DOWN buttons, adjust to appropriate DAY
of week.
c. Touch the MODE button. AM / PM indicator will flash. Use
the UP and DOWN buttons to set appropriate time.
AM / PM will change automatically once you pass 12:00.
d. Touch the MODE button, MINUTES will flash. Use the UP
and DOWN buttons to set MINUTES to the appropriate
time.
e. After the last parameter is set, touch the MODE button to
lock in your settings.
3. Once the installer has performed the initial setup, power
down the unit by touching the POWER button if no other pro-
gramming will be done at this time.
NOTE: The unit is programmed with default time and tempera-
ture settings for the Automatic Mode (see below). If these set-
tings are satisfactory, then skip “Programming the Thermostat for
Automatic Mode” and continue to the other programmable
options under “Customizing Heater Settings”.
Default settings for Automatic Mode:
Period Time Setpoint
1. Wake Up 6:00 AM 70°F (21°C)
2. Daytime 8: 00 AM 62°F (17°C)
3. Evening 6:00 PM 70°F (21°C)
4. Sleep Time 10:00 PM 62°F (17°C)
Customizing Heater Settings
The heater has three modes of operation, Automatic (Heat)
Mode, Ventilation Mode, and Hold Mode with five user
programmable options, 7 Day Programmable Thermostat,
Lockout Setting, Volume Adjustment, Centigrade/Fahrenheit, and
a Nightlight.
NOTE: For the following setup procedures, the display will auto-
matically save the setting after a 30 second pause and return to
the previous operating setting. If this occurs, start back at Step 1
of the procedure.
Programming the Thermostat for Automatic Mode
The 7 day programmable thermostat can be customized for two
categories, Weekdays (Monday-Friday) and Weekends (Saturday
& Sunday). Each category has 4 periods, see the Default set-
tings above for an example. Set a start time and temperature for
each period:
1. Simultaneously touch and hold the POWER and MODE
buttons for 1.5 seconds. MON through FRI will display with
the hour and Period 1. This is your wake-up time.
2. Touch MODE button once to start programming the HOUR
for Period 1 (Monday through Friday). Touch either the UP or
Down buttons to set the hour for START time.
3. Touch MODE button again to program the MINUTES for
Period 1. Touch the UP or DOWN buttons to set MINUTES.
4. Touch MODE button again to start programming the
TEMPERATURE for Period 1 (Wake Up). Touch the UP or
Down buttons to set temperature for Wake Up.
5. Touch the MODE button again to move to Period 2 and follow
steps 2 through 4 for each of the remaining periods. Once
the Weekdays (Monday through Friday) are set, touching the
MODE button again will move to the Weekend settings.
Follow steps 2 through 4 again for the weekend settings.
6. Once the previous steps are complete, touch the MODE but-
ton once more to lock the settings or wait 30 seconds and
the unit will lock the settings automatically. Once the settings
have been locked the unit will begin normal operation.
Hold Mode (Vacation Setting)
The HOLD mode overrides the programmed settings and is use-
ful when a constant temperature needs to be maintained for
comfort or can be set at a lower temperature for times when the
area is unoccupied for long periods (vacation setting) or if freeze
protection is needed in colder climates.
1. Touch MODE button once to activate the display and touch
the MODE button again until the HOLD indicator appears.
2. Touch the Up or Down buttons to set temperature to your
“Hold” temperature. During HOLD mode, default settings
along with the automatic rotation of the 4 periods will be dis-
abled. The heater will operate from the current setting, where
the setpoint can be adjusted.
3. To exit out of the HOLD mode, the user has to press the
MODE button.
NOTE: HOLD mode setting will not be saved after exiting.
Ventillation Mode
This heater also has the option to use as a FAN ONLY device. Heat
will not be produced, but the ventilator fan will operate to provide a
nice gentle breeze to circulate the air.
Touch the MODE button until you see the FAN icon illuminate and flash.
Use the Up or Down buttons to increase or decrease the fan speed.
NOTE: The fan icon will flash for 3 seconds. After 3 seconds, the
heater will enter Fan Only Operation. Touching the MODE button
again will switch the heater into another operation.
Celsius / Fahrenheit Indication
The default temperature scale for the heating unit is Fahrenheit.
To change the temperature scale, simultaneously touch and hold
the MODE and DOWN buttons for 1.5 seconds. Notice the C
indicator illuminates. Touch both buttons again to change back
to the F (Fahrenheit) scale.
Lock Out Feature
Touch and hold the POWER and DOWN buttons simultaneously
for 1.5 seconds. Notice that the Padlock symbol will be visible.
Touch and hold both buttons again to toggle Padlock symbol ON
or Padlock symbol OFF.
NOTE: With the Padlock symbol ON, the unit is locked (the
POWER button is functional, the normal functions of the other
buttons are disabled).
Night Light Operation
Touch and hold MODE and UP Buttons simultaneously for 1.5
seconds. Notice that the NIGHT LIGHT (Light bulb) indicator will
be visible and the backlight will illuminate at 100% brightness.
Touch both buttons again and the NIGHT LIGHT indicator and
backlight will turn OFF.
5