Quick Charge Fuel Gauges User Manual

Led battery fuel gauge

Advertising
background image

LED BATTERY
FUEL GAUGE

QUICK CHARGE

BATTERY MESSENGER

“LIMITED WARRANTY”

Quick Charge corporation warrants the Battery Fuel Gauge (BFG) for Five (5) years from the date
of purchase.
After the warranty period, units returned to the factory for repair will be charged a minimum rate of
$25.00 each. BFG will be returned, freight and repair charges, C.O.D. unless other arrangements
have been made.
This warranty covers all defects in manufacture and performance, provided the unit is operated in
compliance with manufacture’s operating instructions. For repairs to be made at the Quick Charge

factory, a FM and/or component(s) should be sent, freight prepaid to Quick Charge at:

Quick Charge Corp.

1032 S.W. 22nd St.

Oklahoma City, OK. 73109

Quick Charge, will at it’s option, repair or replace the BFG or component in question. The repaired
item will then be returned, freight prepaid by Quick Charge. This warranty is void if the BFG or
component have been altered, changed, or repaired by anyone not authorized by Quick Charge, or
if the BFG or component, have been subjected to misuse, negligence, or harsh environmental
conditions. Field repairs are made at the user’s own risk. “Authorization” by Quick Charge to repair
refers to maintaining the warranty only. Quick Charge assumes no responsibility or liability for field
servicing, and shall not be responsible for incurred travel or labor charges.
Quick Charge corporation shall not in any event be liable for the cost of any special, indirect or
consequential damages to anyone, product or thing. This warranty is in lieu of all other warranties
expressed or implied. Quick Charge neither assumes nor authorizes any representative or other
person to assume for us any liability in connection with the sale of this product.


INTRODUCTION:
The Fuel Gauge is designed to monitor and display the state of charge on motive power
(deep cycle) batteries.

SOM E APPLICATIONS:
Golf cars, pallet trucks, forklifts, personnel carriers, scissor lifts, floor scrubbers, EV’s,
bass boats.

INSTALLATION:

CAUTION: Always wear protective eye shields and clothing when working with
batteries. Batteries contain acids which can cause bodily harm. Do not

put wrenches or other metal objects across the battery terminal or
battery top. Arcing or explosion of the battery can result. Do not wear
jewelry when working around batteries. Arcing can cause sever burns.

Locate a place to mount the gauge. Mark the two mounting tab holes on the surface to be
mounted. Use a 1/8" drill. Use a 3/8" drill bit to pass all the wires through so that the gauge
mounts flush.. Be sure hole is bur free. Use sheet metal or appropriate screws to mount.

Attach red wire of meter to +battery . Black wire to - battery. Ideally, the wires need to go
directly to the battery. If this is not possible, use leads from studs, terminals or any other
contact points as close to the battery as possible. The meter must see battery voltage all the
time, connect before switches, contactors or anything else.

The fuel gauge may be connected with the key switch so that it will illuminate only when
switch is turned on. Connect the blue wire to a positive wire at the key switch so that when
it is turned on, power is applied to the blue wire. NOTE: If you do not want to use the key
switch feature, you must connect the blue wire to the red wire.

OPERATION:
When connected for the first time, the gauge will read static battery voltage. The bars will
light in increments as the battery is charged or discharged giving you an accurate reading
of your battery’s capacity all the time. When the battery is being discharged you will notice
a secondary ghost light bar operating in the background that will give you an indication
of how much energy you are using. The last bar of the primary light bar will flash at 1.75
volts per cell. The battery should not be discharged beyond this point, and should be
recharged as soon as is possible. Never charge a hot battery, let it cool down first. The last
LED bar will also flash at a static voltage of 2 volts per cell.

Advertising