Vitek VT-3625 - Manual (Page 4)

VT-3625
Car Audio CD/MP3 player, MW/FM stereo
receiver with auto-tune system, RDS radio
information system with swinging removable
front panel.
PARTS DESCRIPTION AND OPERATING FEA-
TURES
1. Power on/off ( )
2. Function selector button (SEL): bass/treble/bal-
ance/ Fader/ TA search / DPI mask /enter/vol-
ume/antishock system/ beep/scan/Radio oper-
ating mode/radio settings/backlight/ volume
level setup
3. Volume up/down, level setting for
bass/treble/balance/fader
4. Stations preset (1,2,3,4,5,6)
5. ‘AF’ Function (alternate frequencies)
6. ‘TA’ Function (traffic information)
7. ‘PTY’ Function (Program type)
8. Display button (DISP)
9 Mode button (MODE)
10.Band button (BAND)
11.Automatic or manual setting (frequency up or
frequency down / CD track selection /search
button
12.Automatic Program Search Function (A/PS)
13.Audio equalizer settings (EQ)
14.Auto-tuning “SCAN” feature (SCAN)
15.Sound mute button (MUTE)
16.LCD Display
17.Open button ( )
18.CD opening
19.CD Eject ( )
20.Pause button (PAUSE)
21.Intro mode playback (INT) (For previewing
tracks)
22.Track repeat button (RPT)
23.Random track selection (RDM)
24.25.+ 10 track search up/down
26.Cancel and reset button (RESET)
INSTALLATION
Preliminary Notes
• Carefully choose the installation location so that
the device will not impede the normal operation
of the automobile.
• Avoid installing the device in places where it may
be subjected to sources of high temperatures,
such as direct sunlight, hot air from the heater,
or where it can me damaged by dust, dirt or
excessive shock.
• For safe and reliable installation, use only the
parts provided.
• Remove the front panel before installing the
device.
Setting the installation angle
The allowable degree of slant from the horizon-
tal position is no more than 20°.
Installation Example
Installing in a dashboard (PIC. 1-4)
Note: Store the key in a reliable place as you
may need to remove the device from the car in
the future.
Removal and installation of the front panel
The front panel of this device can be removed in
order to avoid theft.
Removing the front panel
Press the ( ) button (17) in order to make it
possible for the front panel to move into the hor-
izontal position (PIC. 5).
Press the button on the back side of the panel
and pull forward in order to disconnect the panel
and carefully remove the panel from its holding
bracket (PIC. 6).
Place the front panel into the protective case
supplied with the radio for safekeeping (PIC. 7).
Be careful when handling the front panel!
1. Do not drop the front panel
2. Do not press on the screen during installation
and removal.
3. Do not touch the contacts on the panel or the
main device – that can lead to poor electrical
contact.
4. Dirt or foreign matter should be removed with a
clean, dry cloth.
5. Do not subject the panel to heat or direct sun-
light.
6. Do not allow the panel to come into contact with
flammable substances or solvents.
7. Do not attempt to take the front panel apart.
Installing the front panel back into place
(PIC. 8)
After the holding bracket returns to its initial
(vertical) position, place the front panel into the
bracket. Place one side of the front panel into
the proper position and then press the other
side of the panel into position until you hear it
“click.”
Note: If the panel is installed in the wrong posi-
tion, several regulators may not work and parts
of the display will not light. If this happens press
the ( ) button and reinstall the front panel.
ENGLISH
4
3625_4l.qxd 29.03.05 16:39 Page 4