La Crosse Technology WS-9060U-IT - Manual

1
LCD
Display
Function key
Stand
Function keys
WS-9060U-IT WEATHER STATION
Instruction Manual
INTRODUCTION:
Congratulations on purchasing this state-of-the-art
weather station as an example of innovative design and
quality piece of engineering. Provides time, calendar,
weather forecast, moon phase, indoor and outdoor
temperature, indoor and outdoor relative humidity. This
unit will never keep you guessing on current and future
weather conditions. Operation of this product is simple and
straightforward. By reading this operating manual, the user
will receive a better understanding of the Weather Station
together with the optimum benefit of all its features.
FEATURES:
The Weather Station
x 12/24 hour time display
x Calendar display (year shows only in set mode)
x Display 8 Moon phases throughout the year
x Weather forecasting with weather tendency indicator
Battery
compartment
Hanging
hole
2
x Indoor and outdoor temperature display with
MIN/MAX records
x Temperature display in ºC/ ºF
x Indoor and outdoor humidity display
x Humidity data display as RH%
x Low battery indicator
x Table standing or wall mounting
Thermo-Hygro Transmitter
DO NOT MIX OLD AND NEW BATTERIES.
DO NOT MIX ALKALINE, STANDARD, OR
RECHARGEABLE BATTERIES
TO INSTALL AND REPLACE BATTERIES IN THE
THERMO-HYGRO TRANSMITTER
The outdoor thermo-hygro transmitter uses 2 x AAA, IEC
LR3, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
1.
Remove the battery cover.
2. Insert the batteries, observing the
correct polarity (see battery
compartment marking).
3. Replace the battery cover on the unit.
Note:
When changing batteries in any of the units,
all units need to be reset by following the set
up procedures. This is due to a random
security code assigned by the transmitter at start-up. This
code must be received and stored by the weather station
in the first 3 minutes of power being supplied to the
transmitter.
x Remote transmission of outdoor
temperature and humidity to
weather station by 915MHz.
x
Wall mount bracket.
x
Mount in a sheltered place.
x
Avoid direct rain and sunshine
3
TO INSTALL AND REPLACE BATTERIES IN THE
WEATHER STATION
The weather station uses 2 x AAA, IEC LR3, 1.5V
batteries. To install and replace the batteries, please follow
the steps below:
1. Insert finger or other solid
object in the space at the
bottom center of the
battery compartment and
lift up to remove the
cover.
2. Insert batteries observing
the correct polarity (see
marking).
3. Replace compartment
cover.
BATTERY CHANGE:
It is recommended to replace the batteries in all units on
an annual basis to ensure optimum accuracy of these
units.
Please participate in the preservation of
the environment. Return used batteries to
an authorized depot.
SET UP
1. First, insert the batteries in the transmitter (see “To
install and replace batteries in the thermo-hygro
transmitter” above). Keep 5-10 feet from the
display for 15 minutes during set up.
2. Within 2 minutes of powering up the transmitter,
insert the batteries in the Temperature Station (see
“To install and replace batteries in the weather
station” above). Once the batteries are in place, all
segments of the LCD will light up briefly. Following,
the indoor temperature/humidity and the time, as
12:00 will be displayed. If this information is not
displayed on the LCD after 60 seconds, remove the
batteries and wait for at least 60 seconds before
reinserting them. Once the indoor data is displayed
user may proceed to the next step.
3. After the batteries are inserted, the weather station
will start receiving data signal from the transmitter.
4
+ key
MIN/MAX key
SET key
The outdoor temperature and humidity data should
be displayed on the weather station. If this does not
happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
4. In order to ensure sufficient 915 MHz transmission
however, the distance between the Weather Station
and the transmitter should not be more than 330
feet (100 meters) (see notes on “Positioning” and
“915 MHz Reception”).
Note:
When changing batteries in the units, ensure the batteries
do not spring free from the contacts. Always wait at least
15 minutes after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
FUNCTION KEYS:
Weather Station:
The Weather Station has 3 easy to use function keys: 1
key on the front, and 2 keys on the back
SET key
x Press and hold the key to enter manual setting
modes: manual time setting, and calendar
+ key
x Increase, change, toggle all values in manual set
mode
MIN/MAX key
x Press shortly to toggle between indoor and outdoor
MAX/MIN temperature and current temperature