Airaid 300-269 - Manual

Installation Instructions
For Part Numbers:
300-269
720-472 Airaid Oiled Media Filter
301-269 721-472 SynthaMax Dry Media Filter - Red
302-269 722-472 SynthaMax Dry Media Filter - Black
303-269 723-472 SynthaMax Dry Media Filter - Blue
1994-02 Dodge Ram 2500/3500
5.9L I6 Cummins Diesel
Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Cool Air Box 1
4. Heat Shield 1
5. Silicone Reducer 1
6. Weather Strip 36 1/2” 1
7. 1/4 x 20 Button Head Screw 7
8. ¼” Flat Washer 7
9. 6mm Flange Nut 3
10. ¼” x 20 Flange Nut (Optional) 3
11. 1/4” Fender Washer 3
12. 1/4” ID Grommet 3
13. #64 Hose Clamp 1
14. #80 Hose Clamp 1
2. Remove the factory air filter from the lower half of
the factory airbox. 3. Locate the fender air scoop inside of the factory air
box and remove it by pulling outward. The remaining
factory airbox half can now be removed by simply
pulling upward and off of the mounting studs on the
inner fender well.
7. A) Install the CAB and Tube assembly onto the
turbo inlet first, then rotate the assembly downward
onto the inner fender studs. B) Secure the Silicone
reducer to the turbo inlet using the # 64 Clamp (#13).
C) Fully tighten the thr ee 1/4” Button Head Bolts
from step 4.
6. A) Remove the Factory 8mm fender bolt and set
aside, it will be reused later in step
8 . B) Place the
1/4” I.D. Grommets (#12) over each of the three studs
on the inner fender.
8. A) Deter mine the stud size of your par ticular
vehicle, and secure the CAB using the appropriate
washers and nuts. Vehicles with SAE studs will use
the 1/4” x 20 Flanged Nuts (#10) and three Fender
washers (#11).Vehicles with Metric studs will use the
6mm Flanged Nuts (#9) and three Flat Washers (#11).
B) Re install the Factory 8mm bolt thr u the CAB
and into it’s original location.
4. Attach the Intake Tube (#2) to the Cool Air Box,
(CAB) (#3) using three 1/4” Button Head Bolts (#7)
and Flat Washers (#8) as shown. Do not fully tighten
the bolts at this time. 5. A) Install the aluminum Heat Shield (#4) onto the
CAB using the four 1/4” Button head Bolts (#7)
and the Flat washers (#8). Remove the protective film
from Heat Shield. B) Install the silicone reducer (#5)
on to the Airaid Intake Tube (#2) using the #80 (#14)
Hose Clamp.
9. Install the Airaid Premium Filter (#1) onto the In-
take tube as shown and tighten the clamp. Install the
Weatherstrip (#6) onto the top edge of the CAB star-
ing from the front and work your way back
1. Disconnect the negative battery cables.
A) Loosen the hose clamp on the factory tur bo inlet
tube. B) Unfasten the Four clips on the right, left, and
back side of the airbox. Remove the airbox lid and
tube as an assembly and set aside.
A.
B.
A
B
A
B
B
B
A
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.