Airaid 510-213 User Manual
Installation instructions, Component identification
Installation Instructions
For Part Numbers:
510-213
720-476 Airaid Oiled Media Filter
511-213
721-476 SynthaMax Dry Media Filter - Red
512-213
722-476 SynthaMax Dry Media Filter - Black
513-213
723-476 SynthaMax Dry Media Filter - Blue
2007-2015 Toyota Tundra/Sequoia 5.7L V8
2007-2013 Toyota Tundra 4.6L V8
2008-2012 Toyota Sequoia 4.6L V8
Component Identification
1
Airaid Premium Filter
1
2
Intake Tube
1
3
MAF Panel
1
4
Bottom Panel
1
5
Filter Adapter
1
6
Urethane Hump Hose
1
7
Silicone Reducing Coupler
1
8
Weather Strip 37 ½”
1
Hardware and Instructions
1
9
6-32 x 5/16" Phillips Head Screw 4
10
#6 Flat Washer
4
11
Kep Nut
4
12
8-32 x ⅜" Button Head Screw
2
13
Button Head Cap Screw
6
14
1/4" Flat Washer
8
15
¼-20 Flange Nut
3
16
10-32 Well Nut
1
17
10-32 Hex Bolt
1
18
#10 Fender Washer
1
19
12mm Hex Bolt
2
20
Hose Clamp #52
1
21
#56 Hose Clamp
1
22
#72 Hose Clamp
2
23
Barbed Fitting
1
24
½" Barbed Connector
1
25
3/4 Speed Clamp
2
26
1/2" Breather Hose
1
27
Double Bend Bracket
1
28
L Bracket
1
29
#203 Bracket
1
1. Disconnect the negative battery cable.
Remove the factory beauty cover.
A) Loosen the hose clamp on the factory intake
tube where it connects to the throttlebody.
B) Disconnect the Mass Air Flow sensor wiring
harness.
C) Unsnap the wiring harness anchor from the
factory airbox lid.
2. Disconnect the factory breather hose, and vac-
uum hose from the factory airbox lid.
3. Unlatch the four metal clips that hold the air-
box lid to the base and remove the intake tube and
lid from the vehicle. Remove the factory air filter
from the airbox base.
4. Using a 10mm socket, loosen the two bolts
that hold the airbox base to the fender well, and
remove it from the vehicle. There is one bolt on
the front of the base, and one bolt at the rear of
the base.
5. Remove the rear ground anchor bolt from the
side of the fender well and save it for reuse in
step #7 .
6. Assemble the Cool Air Dam panels (#3 & #4)
as shown using four 6-32 screws (#9), washers
(#10), and keps nuts (#11). Install the filter adapt-
er (#5) using three 1/4” button head bolts (#13)
and washers (#14). Install the 3 brackets (#24),
(#25), and (#26) as shown using three 1/4” bolts
(#13), washers (#14), and nuts (#15). Just snug
the bolts for now, they will be adjusted later.
7. Install the CAD assembly into the vehicle.
Align the hole in the bottom over the captured
nut in the fender well. Install one 16mm hex bolt
(#16), and washer (#14). Leave loose for now.
Next reinstall the factory bolt removed in step #5,
thru the bracket, into the ground anchor in the
fender well.
9. Re-install the MAF sensor into the Airaid in-
take tube (#2) as shown using the supplied 8-
32x3/8” button head screws (#12).
Do Not Use The Factory Screws!
Next install the 1/8NPTx3/16” barbed fitting
(#20) into the Airaid tube.
8. Remove two screws, and remove the Mass Air
Flow sensor from the factory intake tube. Note
the orientation of the sensor in the tube. It will
need to be replaced in the same direction in the
Airaid tube.
A.
B.
C.
#203 Bracket
#140 Bracket
#110 Bracket