Kichler 43347 User Manual

Kichler Lighting

Advertising

27) Make wire connections (connectors not provided.) Reference chart below for

correct connections and wire accordingly.

28) Push fixture to ceiling, carefully passing mounting screws through holes in
canopy.
29) Thread knurl knobs onto mounting screws. Tighten knurl knobs to secure

fixture to ceiling.

CABLE LENGTH ADJUSTMENT INSTRUCTIONS

1) Adjust the length of the cables to achieve the desired height of the mounted

fixture. (See cable adjustment detail)

To raise fixture: Push cable up into canopy. Release cable and cable will lock

into place.

To lower fixture: Push button in on cable adjuster and pull cable down.

Release button to lock cable in place.

NOTE: With button pushed in cable will raise and lower. Without button

pushed in cable will only raise up and lock in place.

1) Lower bar with socket cluster down through top of outer shade.
2) Place outer shade with bar over inner shade.
3) Align holes at each end of bar with holes in each bracket on inside of inner
shade.
4) Thread screws down through each hole in bar and into holes in brackets.

Tighten screws to secure inner shade in place.

5) Insert recommended bulbs.
6) Screw threaded pipe into hole in bottom of socket cluster.
7) Thread one hexnut onto end of threaded pipe.
8) Slip one flat washer then one rubber washer over end of threaded pipe.
9) Raise diffuser up to fixture. Pass hole in diffuser over end of threaded pipe.
10) Slip one rubber washer then one flat washer over end of threaded pipe. Thread

hexnut onto end of threaded pipe

11) Thread finial onto end of threaded pipe. Tighten finial to secure diffuser in

place. (DO NOT over tighten.)

12) Determine the amount of stems necessary to achieve desired height of
fixture.

CAUTION: At least one 6" stem must be used.

13) Pass fixture wire from coupling on bar through stem and screw stem to

coupling on top of bar. NOTE: Thread locking compound must be applied to

all stem threads as noted with symbol (3) to prevent accidental rotation of

fixture during cleaning, relamping, etc.

14) Pass fixture wire through remaining stems and screw remaining stems
together.
15) After desired number of stems are assembled to fixture, shorten the cables

just until taut. Refer to Cable Length Adjustment Instructions below.

NOTE: Fixture may be hung with or without loops and chain link.

With loops and chain link:
16) Thread one small threaded pipe into end of each small loop.
17) Pass fixture wire from last stem up through threaded pipe in end of one small

loop. Thread that small loop onto the end of stem.

18) Attach chain link to small loop at end of last stem.
19) Attach second small loop to end of chain link.
20) Pass fixture wire through hole in second small loop.
21) Pass fixture wire from second small loop through hole in canopy. Lower

canopy down over stem. Pass hole in canopy over threaded pipe at end of

second small loop.

22) Pass fixture wire through hole in lockwasher. Thread lockwasher onto threaded

pipe protruding from inside of canopy. Pass fixture wire through hole in

hexnut. Thread hexnut onto threaded pipe.

FOLLOW STEPS 23-29 TO COMPLETE INSTALLATION.

Without loops and chain link:
16) Pass fixture wire from end of last stem through one small threaded pipe.

Thread small threaded pipe into end of last stem.

17) Pass fixture wire through hole in canopy. Lower canopy down and pass

hole in canopy over end of threaded pipe on stem.

18) Pass fixture wire through hole in lockwasher. Thread lockwasher onto threaded

pipe protruding from inside of canopy. Pass fixture wire through hole in

hexnut. Thread hexnut onto threaded pipe.

FOLLOW STEPS 23-29 TO COMPLETE INSTALLATION.

23) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work without shutting off

the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home. Place the main

power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s), that

control the power to the fixture or room that you are working on.

c) Place the wall switch in the “OFF” position. If the fixture to be replaced

has a switch or pull chain, place those in the “OFF” position.

24) Find the appropriate threaded holes on mounting strap. Assemble mounting

screws into threaded holes.

25) Attach mounting strap to outlet box. (Screws provided). Mounting strap can be

adjusted to suit position of fixture.

26) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a hole and two raised

dimples. Wrap ground wire from outlet box around green ground screw,

and thread into hole.

B) On fixtures where a cupped washer is provided. Attach ground wire from

outlet box under cupped washer and green ground screw, and thread into

mounting

strap.

If fixture is provided with ground wire. Connect fixture ground wire to outlet

box ground wire with wire connector. (Not provided.) After following the above

steps. Never connect ground wire to black or white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black

White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)

Neutral Wire

Date Issued: 8/1/14

IS-43347-US

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.