Kichler 43461 - Manual

SEMI-FLUSH INSTALLATION
1) Pass fixture wire through center stem. Screw center stem to
top of fixture body.
2) Slip bottom notched end of side bracket in between arm
and center trim piece of fixture body. Fit notch at end of
bracket around post that connects end of arm to center trim
of fixture body.
3) Slip hole in small trim ring over top end of center stem.
4) Align hole in center trim ring with hole in top of side bracket.
5) Thread end of ball stud through hole in top of side bracket
and into hole in side of center trim ring.
6) Repeat steps 2 - 5 for remaining side brackets.
7) Tighten ball studs after all side brackets have been installed.
8) Pass fixture wire through coupling. Screw coupling onto top
of center stem.
9) Screw small threaded pipe into end of coupling on top of
center stem.
10) Pass hole in canopy over threaded pipe. Set canopy on top
of center stem.
11) Slip lockwasher over threaded pipe protruding from inside of
canopy and screw hexnut onto threaded pipe.
12) Follow steps 14-20 in Chain Drop Installation Instructions.
CHAIN DROP INSTALLATION
1) Pass fixture wire through center stem. Screw center stem to
top of fixture body.
2) Slip bottom notched end of side bracket in between arm
and center trim piece of fixture body. Fit notch at end of
bracket around post that connects end of arm to center trim
of fixture body.
3) Slip hole in small trim ring over top end of center stem.
4) Align hole in center trim ring with hole in top of side bracket.
5) Thread end of ball stud through hole in top of side bracket
and into hole in side of center trim ring.
6) Repeat steps 2 - 5 for remaining side brackets.
7) Tighten ball studs after all side brackets have been installed.
8) Pass fixture wire through coupling. Screw coupling onto top
of center stem.
9) Thread one small threaded pipe into end of each small loop.
10) Attach small loop to coupling on top of center stem.
11) Pass threaded pipe at end of second small loop through
hole in canopy.
12) Slip lockwasher over threaded pipe protruding from inside of
canopy and screw hexnut onto threaded pipe.
13) Attach chain link to small loop at end of stem and to loop on
canopy.
14) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
15) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
16) Attach mounting strap to outlet box. (Screws not provided)
Mounting strap can be adjusted to suit position of fixture.
17) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
18) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
19) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
20) Thread threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to ceiling.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 8/9/13 IS-43461-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
COUPLING
ACOPLAMIENTO
MOUNTING STRAP
PLANCHA PARA MONTAR
THREADED BALL
BOLA ROSCADA
CANOPY
CAPUCHÓN
LOOP
ANILLO
LOCKWASHER
ARANDELA DE
SEGURIDAD
HEXNUT
TUERCA HEXAGONAL
LOOP
ANILLO
CENTER TRIM RING
ANILLO DE LA
GUARNICIÓN CENTRAL
BALL STUD
ESPÁRRAGO DE
CABEZA ESFÉRICA
CENTER STEM
VÁSTAGO CENTRAL
SIDE BRACKET
SOPORTE LATERAL
CENTER TRIM
GUARNICIÓN CENTRAL
ARM
BRAZO
LOCKWASHER
ARANDELA DE
SEGURIDAD
HEXNUT
TUERCA HEXAGONAL
CANOPY
CAPUCHÓN
CENTER TRIM RING
ANILLO DE LA
GUARNICIÓN CENTRAL
CENTER STEM
VÁSTAGO CENTRAL
COUPLING
ACOPLAMIENTO