Kichler 49580 User Manual

We’re here to help

Advertising

1) To install glass panels: Carefully insert glass panel inside

cage. Fit top edge of glass panel into channel along top

inside of cage. Press glass panel up against inside of cage.

Place bracket inside cage. Align hole in step of bracket with

hole in bottom edge of cage. Thread screw up through hole

in bracket and into hole in cage. Tighten screw to secure

bracket and glass panel in place. Repeat these steps for

remaining glass panels.

2) Lower top trim down. Set top trim down on top of fixture.

Align hole in top trim with hole in coupling on top of fixture.

3) Pass end of threaded pipe through hole in top trim. Screw

end of threaded pipe into coupling.

4) Thread loop onto end of threaded pipe protruding from top
trim.
5) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the fixture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the fixture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

6) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
7) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
8) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole

and two raise dimples. Wrap ground wire from outlet

box around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Attach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounting strap.

If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.

9) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.

10) Push fixture to wall, carefully passing mounting screws
through holes in fixture.
11) Thread threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to wall.

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/
OR IN WET LOCATIONS.
12) Mounting surface should be clean, dry, flat and 1/4” larger

that the canopy on all sides. Any gaps between the mounting

surface and canopy exceeding 3/16” should be corrected

as required.

13) With silicone caulking compound, caulk completely around

where back of canopy meets the wall surface to prevent

water from seeping into outlet box.

Date Issued: 12/26/14

IS-49580-US

MOUNTING STRAP

PLANCHA PARA

MONTAR

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black

White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)

Neutral Wire

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

THREADED BALL

BOLA ROSCADO