Impact Reflector Panel (28 x 39") - Manual (Page 3)

3
Page 2 Page 7
DO NOT EDIT
OR REVISE
ARTWORK
We will not approve artwork
which has been altered
by the vendor
FORWARD YOUR PROOFS
to [email protected]
FOR APPROVAL
BEFORE FINAL PRODUCTION
DO NOT BEGIN PRODUCTION
WITHOUT PRIOR APPROVAL OF PROOFS
Congratulations on your purchase of an Impact Reflector Panel. The
reflector materials are reversible gold/silver and black/white. The
rotating/tilting bracket can hold the reflector in horizontal or vertical
position at at any angle. The bracket’s tilt locks with a geared tooth locking
mechanism and floating lever. The Impact Reflector Panel is compact and
lightweight, while being quick and easy to set up.
Please follow these instructions to assemble your Impact Reflector Panel.
There are four parts to your Impact Reflector Panel contents:
• Mounting bracket with flex rod adapter
• Two reversible reflector fabrics
• Four flex rods
• Carry bag
Introduction One-Year Limited Warranty
This instructions in this manual use an RP-2839 Reflector Panel to demonstrate assembly and
break-down. The RP-3570 Reflector Panel assembles by the same method. All photos in this
manual are for illustration purposes only. Light stands are not included with Impact Reflector
Panels unless purchased as a kit.
Impact provides a limited warranty to the original purchaser that this product is free from
defects in materials and workmanship under normal consumer use for a period of one (1) year
from the original purchase date or thirty (30) days after replacement, whichever occurs later.
Impact’s responsibility with respect to this limited warranty shall be limited solely to repair or
replacement, at Impact’s discretion, of any product that fails during normal consumer use.
Inoperability of the product or part(s) shall be determined by Impact. If the product has been
discontinued, we reserve the right to replace it with a model of equivalent quality and function.
To obtain warranty coverage, contact Impact to obtain a return merchandise authorization
(“RMA”) number, and return the defective product to Impact, along with the RMA number and
proof of purchase. Shipment of the defective product is at the purchaser’s own risk.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration,
abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, IMPACT MAKES
NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also
have additional rights that vary from state to state.
www.impactstudiolighting.com © Copyright 2013 Gradus Group
IMPACT
A Gradus Group Brand
TM
Page 6 Page 3
DO NOT EDIT
OR REVISE
ARTWORK
We will not approve artwork
which has been altered
by the vendor
FORWARD YOUR PROOFS
to [email protected]
FOR APPROVAL
BEFORE FINAL PRODUCTION
DO NOT BEGIN PRODUCTION
WITHOUT PRIOR APPROVAL OF PROOFS
Assembly Instructions Recommended Accessories
The reflector material is reversible. Place
the side you wish to use as a reflector face
down on a flat, horizontal surface. Place
the mounting bracket in the center. Insert one of the ends into one of the rod
locating holes on the bracket head.
1 2
Insert the other end of the flex rod into a
pocket in the corner of the reflector. Insert a second flex rod into a rod locating
hole on the bracket head next to where
you placed the first flex rod.
3 4
Impact Light Stand
The Impact LS-6B Light Stand is one of
the most economical light stands
available. It extends to a maximum height
of 6 ft, and has a standard 5/8˝ stud on
top with a 1/4˝-20 thread.
Impact Super Clamp
The Impact Super Clamp with Standard
Stud has strong jaws that can clamp on
flat surfaces or tubes from 1/2 to 2-1/8
inches in diameter. The clamp includes a
standard (5/8˝) stud that will accept the
Impact Reflector Panel or many other
light fixtures and accessories.
Impact Sandbags
Impact Sandbags come in a variety of
shapes, weights, and are either black or
orange. They are used for anchoring the
bases of light stands and set walls.
The saddle-style sandbags have two
wings so they can be draped over light
stand legs. Each side of the bag has a
hand strap for easy handling and hanging
on hooks. The outer shell is water
resistant, heavy-duty cordura nylon.
Impact Sandbags can be purchased
pre-filled or empty.
www.impactstudiolighting.com
To see these accessories and all of our lighting equipment,
please see your lighting dealer or visit our website: