Setting up your monitor, Movement sensitivity control – Graco Angelcare AC2012P User Manual
Page 8
![background image](/manuals/108517/8/background.png)
8
IMPORTANT: Only use the AC adapters included with your monitor. Do not use these adapters with any
other equipment. Movement Sensitivity Control. The movement sensitivity control is on the back of the
Nursery Unit. The level has been preset to 2.5 (see fig. 3). Do not adjust this unless you receive false
alarms. Refer to the Movement Sensitivity Adjustment section on Pg. 11 for more information. It is extremely
important to follow our instructions for setting the sensitivity level.
Now plug the Sensor Pad cord into the jack on the back of the Nursery Unit marked “Sensor Pad.”
Turn the Nursery Unit on using the switch on the left. The green Power Indicator will light up.
CORRECT
Sensor Pad Centered Turquoise Side Up
INCORRECT
Sensor Pad Off Center
INCORRECT
Sensor Pad Turquoise Side Down
POSITION OF SENSOR PAD UNDER MATTRESS
(Top Down View of Crib)
Sensor Pad
Sensor Pad
CORRECT
INCORRECT
PLACEMENT OF SENSOR PAD CORD
Figure 1
fig. 2
SENSOR PAD
(See figs. 1 and 2)
Place the Sensor Pad under the center of the crib mattress with the blue side facing up. Do not place any loose bedding
or linen between the crib mattress and the Sensor Pad. The Sensor Pad must rest on a flat, firm surface. If your crib has
a spring or slat base, place a piece of Masonite board under the Sensor Pad. This support must measure at least 13
inches long on all four sides and 1/4 inch thick. (You may order a Masonite board directly from us.
Call Graco at 1-800-345-4109). If your crib has a plywood base, your mattress support is firm enough to use the monitor
properly. Only use your Angelcare® monitor in a stationary sleeping environment such as a crib where the Sensor Pad
can rest on a flat, firm surface. Be sure to place the turquoise side of the Sensor Pad facing up.
CAUTION: To avoid potential strangulation accidents resulting from loose cords or wires in the crib, make sure the
Sensor Pad cord passes underneath the mattress entirely. After positioning the Sensor Pad under the mattress, bring the
cord to the corner of the crib and secure it to the top and bottom of the leg of the crib, or wind it around the leg
(see fig. 1).
Setting Up Your Monitor
fig. 3
fig. 1
Movement Sensitivity Control.
- 1762140
- 1762140
- Pack 'n Play 9261
- Lovin' Hug 1751553
- TOT WHEELS 4521
- Assura ISPC116BA
- Baby Accessories
- Lovin' Hug 1755724
- Bumper Jumper 4E02LJG1
- 5070
- UltraClear 2755GM
- ISPH013AB 05/05
- PACK 'N PLAY 9130
- Ultra Clear 1750483
- 9842
- PACK N PLAY 9640
- Pack 'n Play 1751557
- 9749
- 5615
- ISPP027AB
- 1466
- 4118
- Pack 'n Play 1765494
- Lovin' Hug 1760956
- 2797
- Pack 'n Play 9342UNS
- Lovin' Hug 1761642
- 4521
- 9747
- ISPP008AA
- 1136
- ACTIVITY CENTER 4520
- 1465
- Open Top 1494
- 4622
- Jump N Jive 1762254
- ISPP045AB
- 8740
- 2L01VIB
- 9400
- WING 1123
- SnugRide 30
- 8833
- 1760928
- 9415
- ISPB008BC 1/03
- Jumpster 8740
- 4512
- MetroLite PD117207A
- 8446
- 8446
- Jumpster IS8731
- Baby Seat
- 4114
- ISPP066AA
- IMONITOR 2M13
- Travel Lite 1757431
- Swing 'N Bounce 1750230
- TOT WHEELS ENTERTAINER 4440
- 1422
- Baby Carrier
- 3868
- Baby Einstein ISPS037AB 11/05
- CONTEMPO ISPH015AC
- 4033
- ISPC089BA
- Ultra Clear 2700
- Infant Restraint/Carrier
- ISPC008BA 08/02
- Pack 'n Play 1756938
- 4530
- Crib
- ISPP062AA
- Baby Swing
- OPEN TOP SWING 1444
- Lovin' Hug PD112872A
- 844
- Silhouette 1770590
- 5070 Series
- ISPP046AF
- ENTERTAINER 4620
- TOT WHEELS ENTERTAINER 4430
- ISPP072AC
- 9757
- HARMONY ISPH009AA
- PD116616A
- Pack 'n Play 9957CNP
- Silhouette 1764030
- 8444
- ISPS057AC
- Baby Playpen
- Baby Toy
- Lovin' Hug PD120911A
- ISPP056AB
- 4113
- PD121628A
- 2791
- Lovin' Hug 1757214
- ISPP072AB
- ISPP066AB
- ISPP045AC
- 2M17
- 2794
- LISTEN 'N TALK 2770
- ISPP003AA
- UA105
- ISPS055AA
- ISPP004AB
- 1481
- 4650
- 2L00
- 8603COR
- ISPP020AB
- ISPP077AB
- ISPJ002AB
- PD107647A
- 1452 EN
- 1435 ES
- 1495 EN
- 1424 EU