8030a operating manual – Genelec 8030A User Manual

Page 4

Advertising
background image

8030A Operating Manual

Figure 4: The curves above show the effect of the ‘treble tilt’, ‘bass tilt’
and ‘bass roll-off’ controls on the free field response.

Figure 5: The curve group shows the horizontal directivity characteristics
of the 8030A in its vertical configuration measured at 1m. The lower
curve shows the system’s power response.

Bass amplifier output power with an 8 Ohm load: 40 W

Treble amplifier output power with an 8 Ohm load: 40 W

Long term output power is limited by driver unit
protection circuitry.

Amplifier system distortion at nominal output:

THD

< 0.05 %

SMPTE-IM

< 0.05 %

CCIF-IM

< 0.05 %

DIM 100

< 0.05 %

Signal to Noise ratio, referred to full output:

Bass

> 100 dB

Treble

> 100 dB

Mains voltage:

100, 120, 220 or 230 V

according to region

Voltage operating range:

±10 %

Power consumption:

Idle

10 VA

Full output

80 VA

Lower cut-off frequency, –3 dB:

< 55 Hz

Upper cut-off frequency, –3 dB:

> 21 kHz

Free field frequency response of system:

58 Hz – 20 kHz (± 2.0 dB)

Maximum short term sine wave acoustic output on axis
in half space, averaged from 100 Hz to 3 kHz:

@ 1m

> 100 dB SPL

@ 0.5m

> 106 dB SPL

Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver
unit protection circuit):

@ 1m

> 97 dB SPL


Maximum peak acoustic output per pair on top of
console, @ 1 m from the engineer with music material:

> 108 dB

Self generated noise level in free field @ 1m on axis:

< 10 dB (A-weighted)

Harmonic distortion at 85 dB SPL @ 1m on axis:

Freq:

50…100 Hz < 2 %

> 100 Hz

< 0.5 %

Drivers:

Bass

130 mm (5") cone

Treble

19 mm (

3

/

4

") metal dome

Both drivers are

magnetically shielded

Weight:

5.6 kg (12.3 lb)

Dimensions: Height

299 mm

(11

13

/

16

")

(including Iso-Pod™ table stand)

Height

285 mm

(11

1

/

4

")

(without Iso-Pod™ table stand)

Width

189 mm

(7

7

/

16

")

Depth

178 mm

(7")

Connectors:

Input: XLR female, balanced 10 kOhm,

pin 1 gnd, pin 2 +, pin 3 -

Output: XLR male, balanced 100 Ohm

Pin 1 gnd, pin 2 +, pin 3 -


Input level for 100 dB SPL output at 1 m:

-6 dBu at volume control max


Volume control range:

-80 dB relative to max output


Output signal level is 0 dB relative to input signal level
but adjustable by volume control

Crossover frequency, Bass/Treble:

3.0 kHz

Treble tilt control operating range:

0 to –2 dB @ 15 kHz

Bass roll-off control operating in a –6 dB step @ 85 Hz
(to be used in conjunction with a 7050A subwoofer)

Bass tilt control operating range in –2 dB steps:

0 to –6 dB @ 100 Hz

The ‘CAL’ position is with all tone controls set to ‘off’ and
the input sensitivity control to maximum (fully
clockwise).

AMPliFier SecTioN

croSSover SecTioN

SySTeM SPeciFicATioNS

International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83 881

Fax +358 17 812 267

Email [email protected]

In the U.S. please contact
Genelec, Inc., 7 Tech Circle
Natick, MA 01760
Phone +1 508 652 0900

Fax +1 508 652 0909

Email [email protected]

www.genelec.com

Genelec Document D0036R001. Copyright Genelec Oy 5.2004. All data subject to change without prior notice

In China please contact:
Genelec China Representative Office
SOHO New Town, 88 Jianguo Road
D-1504, Chaoyang District, Beijing 100022, China

Phone +86 10 8580 2180 Fax +86 10 8580 2181

Email [email protected]

Advertising