Advanced information – Moultrie GAMESPY M100 User Manual
Page 5
Plot Duration - (default 3 hours) – Plot Duration is used to
limit the time periods that the camera will be active. To
change the plot duration, press the UP/DOWN buttons to
highlight the desired setting. Press the ENTER button to
save the setting and return to the Camera Setup Menu.
Plot duration can be set to All Day, 1, 2, 3, or 4 hours.
• All Day – Plot cam takes photos all day
• 1 Hour – Plot cam takes photos for 1 hour twice a day.
• 2 Hour – Plot cam takes photos for 2 hours twice a day.
• 3 Hour – Plot cam takes photos for 3 hours twice a day.
• 4 Hour – Plot cam takes photos for 4 hours twice a day.
NOTE: Increasing the Plot Duration will decrease the battery
life of the camera. It is recommended to use lithium batteries
for taking plot videos.
Battery Calc - This feature provides an estimated battery
life of the camera. The battery life is expressed as “###
Days”. Pressing the MODE button will return to the
Camera Setup menu.
NOTE: The number of days shown is based on using 8 AA
alkaline batteries with 5 day and 5 night photos per day.
Actual battery life will vary depending on type of battery,
weather conditions and camera usage. It is recommended to
use lithium batteries for best performance.
Default Settings - (default No) -To restore all the settings
back to the factory default, press the LEFT/RIGHT buttons
to highlight the YES setting. Press the ENTER button to
restore the default settings and return to the Camera Setup
Menu.
M100 GameSpy Digital Camera
M100 GameSpy Digital Camera
Page 9
Page 8
Delete All Photos - (default No) - To remove all content
on the SD card, press the LEFT/RIGHT buttons to
highlight the YES setting. Press the ENTER button to
erase photos and return to the Camera Setup Menu.
Security Code - (default "00000") - This feature prevents
unauthorized use of the camera should it become lost or
stolen by requiring a 5 digit security code to be entered to
unlock the camera. The security code is 5 digits, each digit
being a number 0-9. The default code is "00000". Once the
code is changed from the default code, the camera will
prompt you to enter the correct code whenever:
• The camera is turned on
• The camera is woken up from sleep mode
• The camera is connected to USB
If the security code is the default number, then you do not need to
enter the code.
Camera Name - (default MYCAMERA) The Camera
Name is imprinted on the photos and provides a point of
reference when multiple cameras are used. To change the
Camera Name, use the LEFT/RIGHT buttons to highlight
the character to be modified. Press the UP/DOWN button
to select the desired character (A to Z, 0 to 9, dash or
space). Press LEFT/RIGHT to move to the next character.
Press the ENTER button to save the new camera name and
return to the Camera Setup Menu.
Temperature - (default Fahrenheit) - The temperature is
imprinted on each photo and can be in degrees Fahrenheit
or Celsius. To change the temperature units, press the
UP/DOWN buttons to highlight the desired setting. Press
the ENTER button to save the setting and return to the
Camera Setup Menu.
IR Test- (default On) When IR Test is ON, the red AIM
LED light on the front of the camera will illuminate. To
help find the center field of view for the camera, stand out
in front of the camera and move left or right as you observe
the AIM LED - as you walk away from direct center the
LED light will be less bright. As you walk towards center
the LED will appear brighter.
Info Strip - (default On) -When the Info Strip is turned
ON, the information strip, as described in the Advanced
Setup section of this manual, is imprinted on the photos.
The Barometer, Temperature, Moon phase, Date, Time,
Camera Name, & Moultrie logo are imprinted on the
bottom of each picture. When the Info Strip is turned OFF,
the photo contains no information strip. To change the Info
Strip setting, press the LEFT/RIGHT buttons to highlight
the desired setting. Press the ENTER button to save the
setting and return to the Camera Setup Menu.
Plot Frequency - (default 15 seconds) - Used to set the
time frequency between each photo in plot mode. To
change the plot frequency, press the UP/DOWN buttons to
highlight the desired setting. Press the ENTER button to
save the setting and return to the Camera Setup Menu.
Plot frequency can be set to 5, 10, 15, 30, or 60 seconds.
NOTE: Increasing the Plot Frequency will decrease the
battery life of the camera. It is recommended to use lithium
batteries for taking plot videos.
M100 GameSpy Digital Camera
M100 GameSpy Digital Camera
Page 7
Page 10
ADVANCED INFORMATION
VI
VIEWING PICTURES ON COMPUTER VIA USB
1. Plug provided USB cable into the USB port on your Windows 7/Vista/XP
computer.
2. Plug other end of USB cable into the camera's USB port.
3. To access JPG pictures and AVI movie files, navigate to "My Computer" and
double click the "Moultrie CAM" drive. Picture files will be stored In the
DCIM/100_MDGC directory; video files are located in the DCIM directory.
4. To exit USB mode, follow Windows’ instructions for properly disconnecting
a removable drive and then unplug
VIEWING PICTURES - TV OUT
1. To enter TV Out Mode, turn on the camera and place in the SETUP mode.
2. Plug RCA jack on provided TV Adapter Cable into a VIDEO IN port on a
TV or VCR.
3. Plug other end of TV Adapter Cable into the TV Out Jack. Pictures are now
presented on the TV.
4. To view pictures use the RIGHT or LEFT button to sequence to the
next/previous captured picture or video clip. The camera’s menu display shows
the picture number being viewed.
5. To delete current picture or video, press the DOWN button.
6. To exit TV mode, unplug the TV Adapter Cable from the TV Out Jack and
TV or VCR.
MFH-M100