Intel IWILL P4D-N User Manual
Iwill p4d/p4d-n motherboard
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Contents
- 1: Introduction
- Manual Structure
- Manual Features
- If The Motherboard Is Already Installed
- If You Need To Install This Motherboard
- Critical Topics
- Packing List
- Pre-Use Checklist
- 2: Key Features & Components
- Motherboard Layout
- Key Features & Components
- Intel 845 Chipset
- CPU Sockets
- System Memory Sockets
- The AGP Slot
- PCI Expansion Slots
- Drive Connectors
- IDE Drive Connectors
- Floppy Disk Drive Connector
- Other Internal Connectors
- ATX Power Connectors
- CPU & System Cooling Fan Connectors J39, 40, 41
- WOL: Wake On LAN Connector J75
- CD-In & AUX Audio Connectors J69 & J70
- IR Connector J45
- 6-Channel Audio Option Connector J66/67
- Chassis Intrusion Switch Connector JP12
- USB Ports 3/4 Connector J65
- Smartcard Reader Connector J78
- System Management Bus Connector SMB1
- Front Panel Connectors
- Battery Connector BT
- External I/O Ports
- PS/2 Ports
- USB Ports
- LAN Port (Optional by Model)
- Parallel Port
- Serial (COM) Ports
- Audio Jacks & Connectors
- Jumpers
- JP1 Clear CMOS
- JP6 Keyboard Power On
- JP10 Audio Chip
- JP16 Flash Protect
- JP17 LAN Chip
- Software Features
- Using the Power Installer Disc
- Driver Software
- Utility Software
- 3: Motherboard Configuration
- The Default Configuration
- Hardware Configuration: Jumper Settings
- Jumper JP6: Clear CMOS Memory
- Jumper JP4: BIOS Flash Protect
- Jumper JP6: Keyboard Power On
- Jumper JP10: Audio Chip
- Jumper JP17: LAN Chip
- Firmware Configuration: The CMOS Setup Utility
- Using the CMOS Setup Utility
- Reconfiguring the Motherboard
- Hardware Reconfiguration
- Firmware Reconfiguration
- Pre-installation Preparation
- Installing A CPU
- Processor Selection
- Installing The Processor
- Installing the Heatsink
- Installing System Memory
- Memory Specifications
- Memory Configuration Options
- Installing Memory Modules
- System Memory Recognition
- Installing the Motherboard in a System Housing
- Motherboard Installation Procedure
- Connecting Front Panel Components
- Completing System Configuration
- 5: System Configuration
- Installing or Connecting Internal Peripherals
- Installing an AGP Card
- AGP Configuration
- Display Drivers
- Connecting Internal Devices
- Connecting IDE Devices
- Connecting a Floppy Disk Drive
- Connecting External System Peripherals
- Connecting a Display Monitor
- Connecting a Keyboard & Mouse
- Configuring the CMOS Setup Utility
- The CMOS Setup Utility User Interface
- Running the CMOS Setup Utility
- CMOS Setup Utility Program Sections
- Standard CMOS Features
- Advanced Boot Options
- Advanced Chipset Features
- Integrated Peripherals
- Power Management Setup
- PnP/PCI Configurations
- PC Health Status
- CPU Smart Setting
- PC Health Status
- Load Fail-Safe Defaults
- Load Optimized Defaults
- Set Supervisor/User Password
- Save & Exit Setup
- Exit Without Saving
- Installing an OS & Support Software
- Installing an Operating System
- Installing the Support Software
- Installing Windows Drivers
- The Make Driver Utility
- Making & Installing Linux Drivers
- Installing the Utility Software
- 6: Using the Motherboard
- Using System Features
- Front Panel System Controls & Indicators
- System Controls
- Indicator LEDs
- Additional System Features
- Wake-on LAN (WOL)
- Installing & Configuring An IR Port
- Performance Optimization
- System Memory
- Disk Subsystems
- Processor Upgrades & Adjustments
- Troubleshooting
- Hardware Problems
- General Hardware Troubleshooting
- Hardware Configuration Problems
- Plug and Play Problems
- Replacing the System Configuration Record
- Loading Optimized Defaults
- 7: Technical Specifications