Ingersoll-Rand 66M170-XXX-C - Manual

INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 276-4658 y FAX (800) 266-7016 © 2010 CCN 15321524
www.ingersollrandproducts.com
OPERATOR’S MANUAL 66M150-XXX-C
66M170-XXX-C
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED: 11-3-08
REVISED:
8-25-10
(REV. 0 5)
1-1/2" DIAPHRAGM PUMP
1:1 RATIO, METALLIC
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
The original language of this manual is English.
SERVICE KITS
Refer to Model Description Chart to match the pump mate-
rial options.
637118-C for air section repair (see page 6).
637469-XX for fl uid section repair (see page 4).
PUMP DATA
Models . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type . . . . . . . Metallic Air Operated Double Diaphragm
Material . . . . . . . . . . see Model Description Chart
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.53 lbs (25.19 kgs)
Maximum Air Inlet Pressure . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate
(fl ooded inlet) . . . 80 g.p.m. (302.8 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . 0.46 gal. (1.74 lit.)
Maximum Particle Size . . . . . . . . . . . . . 1/2” dia. (12.7 mm)
Maximum Temperature Limits (diaphragm / ball / seal
material)
E.P.R. . . . . . . . . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)
Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)
Nitrile . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)
Santoprene® . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Dimensional Data . . . . . . . . . . . . . . . . . . . see page 8
Noise Level @ 70 p.s.i., 60 c.p.m. c . . . 77.7 db(A)d
Noise Level @ 70 p.s.i., 60 c.p.m. e . . . 107.0 db(A)d
cTested with 93139 muffler assembly installed.
d The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (L
Aeq
) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
eTested with 97117 housing and 97114 ball installed. Hearing protection
is recommended when operating this product.
NOTICE: All possible options are shown in the chart, however,
certain combinations may not be recommended, consult a
representative or the factory if you have questions concerning
availability.
Figure 1
MODEL DESCRIPTION CHART
66M1 X 0 - X X X - C
Center Body Material / Fluid Connection
5 - Aluminum / 1-1/2 - 11-1/2 NPTF - 1
7 - Aluminum / Rp 1-1/2 (1-1/2 - 11 BSP parallel)
Ball Material
2 - Nitrile
C - Hytrel
E - Santoprene
Example: Model #66M150-1EB-C
Fluid Section Service Kit # 637469-EB
66M1X0 - X X X - C
Ball Diaphragm
637469 - X X
Fluid Cap & Manifold Material / Hardware
0 - Aluminum / Carbon steel
Diaphragm Material
2 - Nitrile
9 - Hytrel
B - Santoprene
Seat Material
1 - Aluminum
Fluid Section Service Kit Selection