Schumacher Instant Power 00-99-000656 User Manual

Important safety instructions, Schumacher electric corporation model: ipd-1000

Advertising
background image

Schumacher Electric Corporation

Model: IPD-1000

OWNER’S MANUAL

INSTANT POWER™ Jump Starter & DC Power Source

THIS PRODUCT HAS A SEALED LEAD-ACID BATTERY INSIDE THAT SHOULD BE KEPT AT FULL CHARGE FOR LONGER LIFE.

RECHARGE WHEN FIRST RECEIVED (EVEN IF GREEN CHARGED LED GLOWS), AFTER EACH USE AND EVERY 3 MONTHS.

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

important safety instructions

Someone should be within range of your voice or close enough to

come to your aid when you are working near a lead-acid battery.
Have plenty of fresh water and soap nearby in case battery acid

contacts skin, clothing, or eyes. If acid enters the eye area, rinse

with cold water for at least 10 minutes and get medical help

immediately.
Do not smoke, or use matches or cigarette lighter, or allow any

spark or flame near the battery or engine.
Never operate the power source unit if it has damaged lead wire or

clamps. Have the lead wire replaced by a qualified technician.
Do not permit internal battery to freeze. Never charge a frozen

battery.

handling warning

WARNING: Handling the cord on this product or cords associated

with accessories sold with this product, may expose you to lead,

a chemical known to the State of California to cause cancer and

birth defects or other reproductive harm. Wash hands after

handling.

operating instructions

Warning: Failure to follow instructions may cause
damage or an explosion. Read entire instruction
manual before use.

1. Turn ignition off before making cable connections.
2. Keep clear of fan blades, belts, pulleys and other parts that

may cause injury.

3. Never allow clamps to touch together or to contact the same

piece of metal to prevent sparking.

4. Use in a well-ventilated area.
5. Clamp the red clamp (+) to the positive terminal of the battery.

(For a negative grounded system.)

6. Clamp the black clamp (-) to an unpainted and unmoving part

of the chassis or engine block.

7. You can now crank the engine. If the engine does not start

within 5-8 seconds, stop and wait at least 1 minute before

attempting to start vehicle again.

8. After the engine starts, first disconnect the black clamp and

then the red clamp in that order. Store the clamps on the ears

located on the back of the case.

9. Recharge the product as soon as possible after use.

led indicators
There are 4 LED internal battery status indicator lights. Press the

BATTERY STATUS button on the front of the IPD-1000 to determine

the internal battery power.

Note: Numbers 1–3 below indicate charge level when not connected

to AC power source or placed in docking station cradle.

1. The green CHARGED LED indicates the internal battery is

fully charged.

2. The yellow RECHARGE LED indicates a 50 to 75% charge.

The IPD-1000 may be used but should be recharged as soon

as possible.

3. The red RECHARGE LED indicates a 50% or less charge;

immediately recharge the IPD-1000.

4. The red CHARGING LED indicates the IPD-1000 is charging

(connected to AC power source or placed in docking station

cradle). At full charge, the green CHARGED LED will light.

charging of internal battery

After removing the

IPD-1000

from the carton, charge it overnight

before using even if the green CHARGED LED glows.

1. To charge, plug wall charger adaptor into the CHARGING

ADAPTOR PORT on the front of the device or in the IPD-1000

docking station cradle.

2. Plug the wall charger into a 120V AC electrical wall outlet. The

red CHARGING LED will glow indicating there is power to the

docking station cradle or unit.

3. The CHARGED LED will glow green when the battery has

reached full charge. This could take up to 24 hours on some

charges due to age and condition of the battery. The charger

will automatically drop into a float mode and maintain the

battery at full charge without damaging battery.

WARNING: Keep moisture, flammable materials and metal away

for the cradle/tray. The metal contacts are electrically live and may

spark when in use.

00-99-000656/0506

CHARGING

ADAPTOR PORT

multi-purpose power supply

The IPD-1000 is a power source for all 12 volt DC accessories

equipped with a 12 volt accessory plug. Make sure the device to

be powered is OFF before inserting 12 volt accessory plug into 12

volt accessory outlet located on right side. The DC socket has a 15

amp automatic overload protection circuit breaker. The breaker will

automatically reset after an overload occurs.

Advertising
This manual is related to the following products: