KORG Triton Studio - Manual (Page 232)

Ef
fect
221
066: Comp – Param4EQ
(Compressor – Parametric 4-Band EQ)
This effect combines a mono-type compressor and a four-
band parametric equalizer. You can change the order of the
effect connection.
067: Comp – Cho/Flng
(Compressor – Chorus/Flanger)
This effect combines a mono-type compressor and a chorus/
flanger. You can change the order of the effect connection.
d
[O] Output Level 0...50
Sets the overdrive output level
☞
Fx:006,
Src Off...Tempo
Selects the modulation source for the overdrive output level
Amt –50...+50
Sets the modulation amount of the overdrive output level
e
[O] Low Cutoff [Hz] 20...1.00kHz
Sets the center frequency for Low EQ (shelving type)
Gain [dB]
Sets the gain of Low EQ –18...+18dB
f
[O] Mid1 Cutoff [Hz] 300...10.00kHz
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
Sets the band width of Mid/High EQ 1 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Mid/High EQ 1 –18...+18dB
g
[O] Mid2 Cutoff [Hz] 500...20.00kHz
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
Sets the band width of Mid/High EQ 2 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Mid/High EQ 2 –18...+18dB
h
Routing CMP
→
OD, OD
→
CMP
Switches the order of the compressor and overdrive connection
i
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
a
[C] Sensitivity
Sets the sensitivity 1...100
☞
Fx:002
b
[C] Attack
Sets the attack level 1...100
☞
Fx:002
Output Level
Sets the compressor output level 0...100
☞
Fx:002
c
[E] Trim
Sets the parametric EQ input level 0...100
d
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1 20...1.00kHz
Q
Sets the bandwidth of Band 1 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 1 –18...+18dB
e
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2 50...5.00kHz
Q
Sets the bandwidth of Band 2 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 2 –18...+18dB
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Trim
Parametric 4Band EQ
Output Level
Envelope - Control
Comp
f
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3 300...10.00kHz
Q
Sets the bandwidth of Band 3 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 3 –18...+18dB
g
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4 500...20.00kHz
Q
Sets the bandwidth of Band 4 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 4 –18...+18dB
h
Routing CMP → PEQ, PEQ → CMP
Switches the order of the compressor and parametric EQ connection
i
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
a
[C] Sensitivity
Sets the sensitivity 1...100
☞
Fx:002
b
[C] Attack
Sets the attack level 1...100
☞
Fx:002
Output Level
Sets the compressor output level 0...100
☞
Fx:002
c
[C] EQ Trim
Sets the EQ input level 0...100
d
[C] Pre LEQ Gain [dB]
Sets the gain of Low EQ –15...+15dB
Pre HEQ Gain [dB]
Sets the gain of High EQ –15...+15dB
e
[F] Delay Time [msec]
Sets the delay time 0.0...50.0msec
f
[F] LFO Frequency [Hz]
Sets the LFO speed 0.02...20.00Hz
LFO Waveform
Selects LFO Waveform Triangle, Sine
g
[F] Depth
Sets the depth of LFO modulation 0...100
Feedback
Sets the feedback amount –100...+100
☞
Fx:020
h
[F] Cho/Flng Wet/Dry –Wet...–2:98, Dry, 2:98...Wet
Sets the effect balance of the chorus/flanger
☞
Fx:010, 020
Output Mode Normal, Wet Invert
Selects the output mode for the chorus/flanger
☞
i
Routing CMP → FLNG, FLNG → CMP
Switches the order of the compressor and chorus/flanger connection
☞
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor Chorus/Flanger
Chorus/Flanger
Feedback
LFO: Tri / Sine
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
LEQ HEQ EQ Trim
Comp
Output Level
Envelope - Control