Lasko 5395 - Manual (Page 4)

OPERATION ( Figure 1 and 2 )
The Heater may be operated by the manual controls located
on the Heater (as shown in Figure 1) or by your remote control
(shown in Figure 2).
1. Place the Heater on a firm, level surface, after assembling per this
manual.
CAUTION:
Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The unit
may leave a residue that could darken, stain or leave permanent
blemishes on the finish of certain furniture surfaces, including
wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle with
only the slight movement of the attached cord. Re-
ceptacles in this condition may overheat and pose a
serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
3. When the Heater is initially plugged in, there will be a ‘beep’ and
the power light will come on indicating that there is power to the
unit. The power light will remain lit until the Heater is unplugged
from the electrical outlet.
4. Turn the Heater ON by pressing the ( ).
5. When initially turned on, the Heater will display the current
room temperature in ° Fahrenheit. Press the ( ) and ( ) but-
tons at the same time to change the display to ° Celsius. Press
the same two buttons together again to change the display
back to ° Fahrenheit. The Heater will be in HIGH ( ) heat (1500
Watts).
6. Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500
Watts) and will display the current room temperature.
7. Pressing the ( ) at this point will set the Heater into LOW ( )
heat.
8. To turn the Heater OFF, press the ( ) and unplug the unit from
the electrical outlet.
Rev. G 3/09 4
5395ES Rev. G 3/09 9
5395ES
MODEL 5395
AUTOMATIC TEMPERATURE CONTROL
The automatic temperature function will only operate on "High"
heat ( ). You cannot set the temperature automatically when
the unit is in the low heat mode.
1. To set the room at a specific temperature press the ( ) or ( )
buttons to the desired temperature. The display will now reflect
the ( ) and the temperature will be flashing. The Heater is now
in Auto Temperature Mode.
2. When you reach the temperature at which you want to set the
unit, the set temperature will flash several times and then the
display will return to indicate the current room temperature and
will gradually change as the room temperature changes. NOTE:
the temperature display does not indicate the temperature of
the heated air being emitted by the heater.
3. Once the room temperature reaches 2 degrees above the set
temperature, the Heater will shut off. Once the room tempera-
ture reaches 1 degree below the set temperature, the Heater
will turn back on and continue to cycle off and on to maintain
the set temperature.
4. This function will cancel if the ( ) button is pressed. The Heater
will now be in High heat ( ) and run continuously.
NOTE: It is normal for the Heater “fan” to run for approximately 15
seconds when the Heater shuts off after reaching the set
temperature.
Figure 1
View of Control Panel
The oscillation function will work in any mode. Pressing the ( )
will allow the Heater to oscillate back and forth. To stop the oscil-
lation, press the (
) once more.
Timer Function:
The timer function will work in any mode. The timer function al-
lows you to set the length of operation from 1 hour to 8 hours.
Pressing the Timer Button ( ) will increase the length of opera-
tion by 1 hour each time the button is pressed. Pressing the Timer
Button ( ) once more after the display reflects 8 hours will reset
the Heater to continuously running. Once the timer has been set,
the timer will count down the hours in 1 hour increments, showing
on the display the remaining operating time. The Heater will turn
itself off when the set time has elapsed. The unit can be turned
back on by pressing the Power Button ( ).
Front View of
Remote Control
Figure 2
Rear View of
Remote Control
REMOTE CONTROL (Figure 2)
All the functions performed with the Remote Control work identi-
cally to the manual controls, except that you are unable to change
from °F to °C with the remote control.
1. Install the two “AAA” batteries supplied.
2. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY
EXPLODE OR LEAK.
MODELO 5395
ARMADO (Figuras 1 a 6)
Herramientas Necesarias: Destornillador de Cabeza #2 Phillips
(no incluido)
Retire cuidadosamente el Calefactor de su bolsa y caja. Para
facilitar el armado, coloque el Calefactor de manera que la parrilla
frontal y el panel de control den hacia arriba.
3. Arme la base enclavando las Protuberancias en los Orificios
para Protuberancias. (Figura 3)
5. Alinee el Conjunto de la Base con el Conjunto de Soporte de
Columna. Cerciórese de que la Muesca de Ubicación en el
Conjunto de Soporte de Columna quede alineada con la Llave
en el Conjunto de la Base (Figure 5). Una el Conjunto de la
Base al Conjunto de Soporte de Columna con (4) tornillos M5 X
13 mm. Jale suavemente el Cable Eléctrico para que no quede
holgado, y colóquelo en el Canal Para Cable del Conjunto de
la Base. (Figura 6)
1. Coloque el Cable Eléctrico en la parte inferior del Calefactor.
Pase el Cable Eléctrico por el centro del Conjunto de Soporte
de Columna.
2. Una el Conjunto de Soporte de Columna a la Base del Motor
con (4) tornillos M5 X 13mm. Cerciórese de que la Llave que
está en la Base del Motor quede alineada con la Muesca de
Ubicación en el Conjunto de Soporte de Columna. (Figura 2)
4. Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase el
Cable Eléctrico por el gran orificio que se encuentra del Conjunto
de la Base. NOTA: El canal para cable en la parte inferior de la
base debe estar hacia la parte posterior del Calefactor.
(Figure 4)
Tamaño Real De Tornillos
Figura 3
Protuberancias
Figura 5
Conjunto de
la Base
Conjunto de
Soporte de
Columna
Orificios
para
Protuberancias
Llave
Cable Eléctrico
Figura 1
(8) - M5 X 13mm (2) - M4 X 13mm
Figura 2
Conjunto de Soporte
de Columna
Cable
Eléctrico
Base del
Motor
Llave
Figura 4
Cable
Eléctrico
Conjunto de
la Base
Cable
Eléctrico
Figura 6
Llave
Muesca de
Ubicación
If you lose your remote control, please call Customer Service to
order a replacement at 1-800-233-0268, Monday through Friday,
between the hours of 8:00 a.m. and 5:00 p.m. EST.
+
+