Pioneer S-H810V-W - Manual

Connect the common-side speaker cord
to the HF of LF terminal.
+ +
Connect the hot-side speaker cord to the
HF or LF terminal.
1 Strip the insulation at the tip of the cord
and twist the strands.
2 Turn the thumbscrew anti-clockwise,
make sure that the speaker cord is
inserted well into the hole and turn the
thumbscrew clokwise to fasten into
position.
4
3
HF
HF
LF
LF
1
2
In order to minimize the transmission of vibrations from the speaker to the floor,
Pioneer offers two possibilities :
4 foam cushions to be stuck on the
underside of the speaker system.
4 metal decoupling spikes to be
screwed under the speaker system
(after having unscrewed the 4 metal
feet).
If desired (especially with polished
wood floors), you can also employ the
4 provided metal bases between the 4
decoupling spikes and the floor.
This speaker system is heavy and fragile, and it is therefore dangerous to install it
in an unstable position. For added safety, it is advisable to attach these speakers
to a wall or pillar using chains and hooks (not supplied). To do so, screw the
provided metal ring to the back of the speaker cabinet and then pass a chain or
cable through the metal ring.
The speaker units in this speaker system are magnetically shielded.
However, colours may blur if the speakers are positioned too close to a
television screen. If this happens, switch off the television and switch it
back on again after 15 to 30 minutes. If the problem persists, move the
speakers away from the television set.
BEFORE OPERATION
Thank you for buying this PIONEER product.
Read the Instruction Manual carefully before using this speaker system so that
you can operate it properly. After you have finished, put this manual away in a
safe place for future reference.
The rated impedance of this speaker system is 6 :. It must be connected to a
amplifier which accepts this type of load (miminum and maximum impedances
accepted by the amplifier are generally indicated near the loudspeaker outlets: for
example "4
: to 16 :" or "6 : to 16 :").
To guard against damage to this speaker system due to an electric power
overload, take the following precautions:
Do not supply more than the maximum permitted power to the speaker
system (see Specifications).
Any connection or switching on or off of part of the audio system (CD
player, tuner etc.) must be carried out after switching off the amplifier or at
least with the loudspeaker outlets disconnected (if the amplifier allows).
Interference caused by these operations will otherwise reach the speaker
and may damage the treble loudspeaker units.
When boosting particular frequencies using a graphic equaliser or bass
and treble correctors, make sure that you do not increase the amplifier
volume excessively, as the speaker will be overloaded more quickly.
Do not force a low-power amplifier to produce a high level of sound as
harmonic distortion increases rapidly in this situation and may pose a
danger to the treble speaker units.
Avoid touching the diaphragms and suspensions of speakers units as they are
fragile.
INSTALLATION
CONNECTIONS
Switch off the amplifier power supply (OFF).
Connect the cables to the input terminals on the rear of the speaker: Connect
the neutral cable to the HF or LF terminal and the live cable to the HF or
LF terminal. +
Accessory parts
Instruction Manual ................................................................................................ 1
Warranty ............................................................................................................... 1
Foam cushions .................................................................................................... 4
Decoupling spikes + base ................................................................................... 4
Ring + screw ........................................................................................................ 1
REMARK : The specifications and design of this product are subject to change
without notice, in the interests of improvements.
ADVICES AND PRECAUTIONS :
For optimum sound reproduction of high frequencies, the treble speaker units
must be at the same height as the listener's ears.
For low frequencies, it is possible to increase the level of bass sounds by
positioning the speakers close to a wall (the maximum increase being obtained
for a position in a corner of the listening room).
REMARKS :
For a bi-wiring connection, first remove the cables which link the two pairs of
input terminals labelled HF and LF , and HF and LF .
Check that the cables are securely connected to the terminals. A loose
connection may cause not just intermittent or distorted sound but short-circuiting
and breakdown of the amplifier.
If the cables of one of the speakers have been connected with the wrong
polarities, you will find when listening to a stereo recording that bass sounds are
weakened and the stereo effect normally obtained between the two speakers
does not exist.
Connect the cables to the loudspeaker outlet terminals of the amplifier. Connect
the live cable to the terminal and the neutral cable to the terminal. +
SPECIFICATIONS
Speaker ............................................................... Floor-standing type, bass-reflex
System ............................................................................. 4 ways, 5 speaker units
Woofers ................................................ Cone type, 130 mm x 2
Medium ....................................................... Cone type, 130 mm
Tweeter ......................................................... Dome type, 25 mm
Super-Tweeter ................................... Riffel type, 8 mm x 46 mm
Nominal Impedance ...................................................................................... 6 :
Frequency range ................................................................ 35 Hz to 100 000 Hz
Sensitivity ..................................................................... 89 dB/W at 1 m distance
Maximum power ........................................................................................ 130 W
Dimensions....................................... 250 mm (W) x 1190 mm (H) x 300 mm (D)
Weight .......................................................................................................... 25 kg
Speaker units :
MAINTENANCE OF THE ENCLOSURE
Use a cloth to wipe away dust and dirt.
If the enclosure is very dirty, wipe with a soft cloth dipped in a neutral detergent
diluted five to six times with water, then wipe again with the dry cloth. Do not use
thinner, benzene, cleaning sprays or other chemical products on or near the
enclosures as the surfaces could be adversely affected.
+
+
This product may be covered by one or more of the following patents owned by
GP Acoustics (UK) Ltd. and its affiliates: [Japanese Patent No. 2766862, United
Kingdom Patent No. GB 2 236 929 A, and the United States Patent No.
5,548,657]. To the extent of such coverage, this product has been licensed by
GP Acoustics (UK) Ltd. KEF and UNI-Q are registered trademarks of the GP
Acoustics family of companies.
Do not install the speakers close to an oven or heating appliance. Avoid
exposing them to direct sunlight. High temperatures can distort the structure of
the enclosure and adversely affect the sound.
English
SPEAKER SYSTEM
ENCEINTE ACOUSTIQUE
LAUTSPRECHERSYSTEM
SISTEMA ALTOPARLANTE
LUIDSPREKERSYSTEEM
HÖGTALARSYSTEM
SISTEMA DE ALTAVOCES
SISTEMA DE ALTIFALANTES INSTRUCTION MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG
GUIDA PER L'USO
GEBRUIKSAANWIJZING
BRUKSANVISNING
GUIA DE OPERACIÓN
GUIA DE OPERAÇÃO Published by Pioneer Corporation.
© 2007 Pioneer Corporation.
All reproduction and translation rights reserved.
Printed in China <FRRD-208-B>
+
Discover the benefits of registering your product online at
http://www.pioneer.co.uk (or http://www.pioneer.eu)
http://www.pioneer.co.uk
http://www.pioneer.eu