Tascam MD-350 - Manual (Page 18)

6. Select each character by turning the
[µ TRACK≤ ] dial and pressing
[PUSH ENTER] on the dial.
… If you are using the remote control unit,
select each character with the
[µ TRACK≤] buttons and press the
[ENTER] button to enter it.
7. Repeat steps 5-6.
8. Press the [YES] button after assigning
the disc title.
… The title entry mode for track 1 is
automatically engaged ("001 > _" is
displayed) and the cursor blinks on the
display.
9. Repeat steps 5-6.
10. Press the [YES] button again.
… When the title entry mode for track 2 is
engaged ("002 > _" is displayed), repeat
steps 5-8.
… Repeat the character entry procedure
until all titles have been entered. The
disc title is then displayed if the deck is
in the Stop mode, or if the deck is in the
Play mode, the current track title is
displayed.
… Confirm titles by turning the
[µTRACK≤] dial.
… Press the [ª STOP] button to abort the
operation.
Press the [EDIT/NO] button for more
than 3 seconds (or press the [TITLE
EDIT] button on the remote control unit)
to cancel the title function and resume
playback.
Notes:
… Up to 100 characters can be entered per
track title. However, when the total
number of characters of all track titles
exceeds 1700, no more track titles can
be written onto the MD.
… If the TITLE AUTO INC function is
canceled before all titles have been
assigned, the track title currently being
entered will be erased. Only track titles
which have already been assigned will
be kept.
… If UNDO is performed after TITLE AUTO
INC is completed, the last edited track
title will be canceled.
… Disc and track titles can be assigned
during recording.
… If a track title is assigned while in the
Record-Ready mode during the
overwrit-ing of a track, the track title
will be erased when you resume
recording.
… "DISC" lights while a disc title is being
entered, and "TRACK" lights while a
track title is being entered.
… Assigning titles is unavailable in the
"SHUFFLE MODE" or "PGM MODE".
– 18 –
Titles can be assigned to each disc or
each track using uppercase and
lowercase letters, numbers, "
"
(Katakana) and symbols.
1. Press the [EDIT/NO] button so that
"TITLE ?" is displayed.
2. Press the [YES] button.
… Press the [TITLE EDIT] button if you are
using the remote control unit.
3. Select "DSC" or a track number using the
[µTRACK≤] dial.
… To assign a disc title, select "TITLE >
DSC" ("DSC" blinks).
… To assign a track title, select "TITLE >
XXX (track number)" (Track number
blinks).
4. Press the [YES] button.
"DSC > _ " or "XXX > _ " is displayed.
… The character entry mode is engaged
and the cursor blinks on the display.
5. Press the [DISPLAY] button to select the
character type.
… When " " is lit: Katakana (square
Japanese syllabary) can be entered.
… When " " is lit: Capital alphabet
letters, numerals and symbols can be
entered.
… When no indicator is lit: Small alphabet
letters, numerals and symbols can be
entered.
6. Select each character by turning the
[µTRACK≤] dial and pressing [PUSH
ENTER] on the dial.
Assigning Titles (TITLE Function)
7. Repeat steps 5-6.
… Press the[ª STOP] button to abort the
operation.
… Press the [EDIT/NO] button for more
than 3 seconds (or press the [TITLE
EDIT] button on the remote control unit)
to cancel the title function and resume
playback
8. Press the [YES] button again.
… The disc or track title is displayed again.
… Repeat steps 1-8 to assign titles to other
track numbers.
Select the "CONTINUE" mode with the
[PLAY MODE] button. Titles can be
assigned to the disc and all tracks
successively.
1. Press the [EDIT/NO] button so that
"TITLE ?" is displayed.
2. Press the [YES] button.
… Press the [TITLE EDIT] button if you are
using the remote control unit.
3. Select "TITLE > AINC" with the
[µTRACK≤] dial ("AINC" blinks).
4. Press the [YES] button.
… The disc title entry mode is engaged
("DSC > _" is displayed) and the cursor
blinks on the display.
… The cursor blinks at the first character
position even if a title has already been
assigned.
5. Press the [DISPLAY] button to select the
character type.
Assigning Titles to the Disc and
All Tracks Successively
(TITLE AUTO INC Function)
Buttons used on this page
Editing Recorded MDs
Notas sobre grabación
ª Para proteger un MD contra
borrado accidental
… Después de grabar el MD, deslice la
lengüeta de protección contra
grabación para que el orificio quede
abierto.
… Para grabar el MD otra vez, deslice la
lengüeta para cerrar el orificio.
ª Cuando aparece el mensaje
"Disc Full !!" o "Track Full !!"
El MD no tiene más espacio disponible para
grabar o todas las pistas del MD han sido
utilizadas. Borre las pistas que no necesite
o grabe la música en otro MD.
– 95 –
ESPA
Ñ
OL
ª La forma de asignación de los
números de pista varía
dependiendo de la fuente.
Cuando se reproduce un CD o un MD, y se
lo graba digitalmente seleccionado
[DIGITAL 1] o [DIGITAL 2] con el selector
[INPUT SELECTOR]:
… Los números de pista en el MD grabado
son asignados para adecuarse a los del
CD o MD fuente. Sin embargo, en los
casos abajo listados sólo un número de
pista puede ser asignado a una sección
grabada.
· Una sección compuesta de varias
repeticiones de una sóla pista en un
disco (ej.: empleando la
reproducción repetida de una sóla
pista).
· Una sección compuesta de
grabaciones sucesivas de pistas con el
mismo número de pista provenientes
de más de un disco. También, si la
fuente es un MD, los números de pista
pueden no ser marcadas para pistas
que tengan una duración menor a 3
segundos.
Cuando la fuente es grabada con
[ANALOG] o cuando se graba una fuente
digital que no sea un CD o MD con
[DIGITAL 1] o [DIGITAL 2] estando la
función de pista automática en OFF:
… Toda la grabación puede ser contada
como una sóla pista con un sólo
número de pista asignado a la misma.
· Los números de pista pueden ser
manualmente asignados en los
puntos deseados presionando el
botón [º RECORD] durante la
grabación.
· Los números de pista pueden ser
automáticamente asignados conmut-
ando al función de pista automática
a "A_TRACK > ON" antes de iniciar la
grabación.