Altronix eBridge1CRT Data Sheet - Manual

The eBridge1CRT - IP over Coax transceiver and receiver kit is designed to enable fast
10/100Base-T Ethernet digital communication over coax cable. These plug and play
units facilitate system upgrades from analog to IP cameras/devices utilizing existing
legacy Coax and eliminating the costs and labor associated with installing new network
cabling. In addition data transmission is extended to 2,000’ (over five times the 100m/328’
Ethernet maximum length), eliminating the need for repeaters. eBridge units will transmit
Composite Video Signal with Ethernet data simultaneously.
Input:
• 12VDC to 24VDC Class 2 power supply (polarity not
observed) or 16VAC to 24VAC Class 2 plug-in
transformer.
Power Consumption:
• 12VDC/275mA, 24VDC/110mA,
16VAC/375mA, 24VAC/200mA.
Compliant:
• Incorporates *sloc TM (Security Link over Coax)
technology.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or higher structured cable.
• Distance: up to 328 ft. (100m).
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
• Throughput is rated to pass 25mbps of data at
distances up to 1500 ft. With proper headend
equipment, multiple Megapixel cameras can be used.
Coax:
• Distance: up to 1,500 ft.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• Blue LED - Coax link connection.
• Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
• Green LED - Power.
Environmental:
• Operating Temperature:
14ºF to 122ºF (--- 10ºC to +50ºC).
• Storage Temperature:
-- 22º to 158ºF (--- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing.
Electrical:
• BTU/Hr.:
- VDC: 1.69 - 4.46 BTU/Hr.
Electrical (cont’d):
• BTU/Hr.:
- VAC: 2.46 - 3.07 BTU/Hr.
Accessories:
• Composite video cables (included) - enables
simultaneous composite video signal over the
same Coax.
• Two (2) power connectors.
Applications:
• Retrofit digital IP cameras in an analog CCTV
installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras.
• Extend Network link distance in an industrial
environment.
• Upgrade deployed CCTV Coax to a digital network
for Retail, Casinos, Airports, Schools, Hospitals, etc.
• Enables simultaneous transmission of composite and
digital IP video.
Mechanical:
• Lightweight molded fiberglass reinforced polyester
enclosure is corrosion resistant and does not contain
halogens.
• Dimensions (W x L x H approx.):
2.5” x 3.8” x 1” (63.5mm x 96.52mm x 25.4mm)
• Product weight (approx.): 4 oz. (0.11 kg).
• Shipping weight (approx.): 7 oz. (0.17 kg).
Additional eBridge models:
• eBridge1CR: Single port ethernet receiver
(use with eBridge1CT transceiver).
•
eBridge1CT: Single port ethernet transceiver
(use with eBridge1CR/4CR/16CR receivers).
•
eBridge1CRT: Single port ethernet receiver and
transceiver kit.
•
eBridge4CR: Four (4) port ethernet receiver.
• eBridge16CR: Sixteen (16) port ethernet receiver.
eBridge1CRT - IP over Coax Kit
Rev. DSeBridge1CRT_08012013
Specifications
Overview
Agency Approvals
eBridge1CR
and eBridge1CT
* sloc is a registered trademark of Intersil Corporation.
UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
European Conformity
C-Tick Compliant
Z1409