Simple instruction set (sis) commands – Extron Electronics AVT 200HD Setup Guide User Manual
Page 4
68-1834-50
Rev. A 05 11
4
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics. All rights reserved.
4.
From the Output Configuration submenus, use the Adjustment knobs to select the output resolution, the display type
(4X3 or 16X9), and the display mode (Fill, Follow, or Zoom).
5.
If needed, use the Audio Configuration submenus to select the digital audio type and the language for a second audio
program (SAP).
6.
Configure the comm port settings (serial port baud rate, IP addresses, and DHCP mode):
a.
From any View Comm Setting menu screen, press and hold the Next button, then press and hold the Up (
>
) and
Down (
<
) buttons simultaneously. Hold all three buttons until the Edit Comm Setting menu appears (2 seconds).
b.
On the Edit Comm Setting submenus, rotate the horizontal Adjustment knob (
[
) to move the blinking or angle
brackets to the parameter to be changed, then rotate the vertical Adjustment knob (
{
) to select a value.
7.
Press the Up or Down arrow button to select a channel.
8.
Turn the Volume knob to adjust the volume.
9.
If desired, use the Closed Caption submenu of the Output Configuration menu to turn closed captioning on or off.
10.
Use SIS commands, the Windows-based control software, or the embedded web pages to mute or unmute the audio or
video, configure the closed caption display, and set up the V-chip program blocking as desired.
Simple Instruction Set (SIS) Commands
When setting up the AVT 200HD, you can issue SIS commands from your computer via RS-232 or a LAN connection as an
alternative to the front panel controls. See the AVT 200HD Series User Guide for a complete list of available SIS commands.
Command
ASCII command
(Host to Scaler)
Response
(Scaler to Host)
Additional Description
Select TV standard
E
X$
TVST
}
Tvst
X$
]
Set the TV format
X$
for the incoming RF
signal. For
X$
:
0
= over-the air,
1
= cable standard
2
= cable HRC,
3
= cable IRC
Begin channel scan
E
1TVSC
}
Tvsc1
]
Start scanning for available channels.
Stop channel scan
E
0TVSC
}
Tvsc0
]
Stop scanning for channels.
View tune mode channel list
E
TVCH
}
T
X!.X@
]
T
X!.X@
]
...
]
]
View a list of channels not hidden.
View all presets
E
TVPR
}
P01
•
T
X!.X@
•
Nname
]
...P99
•
T
X!.X@
•
Nname
]
]
View a list of all saved presets.
Select tune mode
E
0TVTM
}
Tvtm0
]
Place the tuner in tune mode.
Select preset mode
E
1TVTM
}
Tvtm1
]
Place the tuner in preset mode.
Select channel by number
(in tune mode)
X!
*
X@
T
}
Tvct
X!.X@
]
Select channel
X!.X@
.
X!
= major number;
X@
= minor number.
Select channel by preset
(in preset mode)
X2%
T
TvprR
X2%
*
X!.X@
]
Select preset
X2%
(which tunes to channel
X!.X@
).
Save a specific channel as a
preset
E
S
X!
*
X@
*
X2%
TVPR
}
TvprS
X2%
*
X!.X@
]
Save channel
X!.X@
to preset
X2%
.
Set output resolution and rate
E
X2^
RATE
}
Rate
X2^
]
Select output resolution
X2^
. For
X2^
:
0 = 480i @ 59.54 Hz, 1 = 480p @ 59.94 Hz,
2 = 720p @ 60 Hz, 3 = 1080i @ 60 Hz.
Select CC service
E
C
X&
TVCC
}
TvccC
X&
]
Select closed captioning service
X&
.
For
X&
:
0
= closed captioning off,
1
-
6
= closed captioning services 1-6.
Enable or disable V-chip for TV
E
T
X3@
*
X1)
VCHP
}
VchpT
X1)
]
Enable or disable the V-chip for blocking
TV shows. For
X1)
:
0
= off,
1
= on.
X3@
= Current V-chip access PIN number
(default is
0000
).