LEDGlow Home Theater Kit - Manual

LED Home Theater Kit
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.
Warning: To reduce the risk of burns, fire, electrical shock, or injury to persons:

Unplug the kit from the outlet before installing or uninstalling any parts.

Close supervision is necessary when this product is used by, or near children, or anyone else who cannot be responsible for their own safety.

NOT intended for recessed installations.

NOT intended for surface installations inside built-in furnishings

Keep cord away from heated surfaces and from children

NEVER operate this kit if it has been damaged or dropped in water
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED HOME THEATER KIT.
Home Theater Kit Includes:

(2) 15 Inch Tubes (A)

(2) 9 Inch Tubes (B)

(1) Control Box

(1) IR Remote

(1) Power Supply

(4) Mounting Brackets

(8) Small Screws

(6) Double Sided Tape

(1) IR Receiver

(2) Sealing Caps for Tubes
Home Theater Kit Installation
1. Arrange the tubes on the ground and test the
kit to ensure proper functionality before moving forward with
the installation.

WARNING: Disconnect all power for
this kit before moving forward with the install. Reconnect
power to the kit after finishing all connections.
DO NOT connect or plug in any cable or tube while you
are installing this kit.
2. Once you know your kit is functioning
properly and have determined your mounting location, ensure
the installation surface is free of dust, dirt, oil, or any other
foreign objects that will not allow the included double sided
take to adhere properly.

NOTE: Rubbing alcohol or any type
of cleaning solution will work best, but be sure the solution
you are using will not affect the mounting surface.
3. Install the mounting clips to your installation
surface using the included double sided tape. Be aware that
over a long period of time this tape may cause some
discoloration to the mounting surface. Remove one side of
the tape protector to apply it to the bottom of the mounting
clip, apply pressure for 5 seconds to ensure proper adhesion.
Repeat this step for the other 3 clips.
4. Place the light bars in the clips by applying
light pressure to the back of the clip. DO NOT apply
pressure to the tube itself, this may cause damage to the tube.
5. Mount the first 9 inch tube to the left side of
your television. Remove the tape protector and firmly press
each mounting clip to your installation surface.
6. Now mount the first 15 inch tube to the top of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.
7. Mount the second 9 inch tube to the right side of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.
8. Mount the second 15 inch tube to the bottom of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.

NOTE: The object of this installation is to install the lights so that the reflected light is visible and not the tubes. The tubes are installed using the
mounting clips so that you can swivel each tube to achieve the best lighting effect possible.
9. Starting with the left hand side tube, connect each tube to the next using the included mini USB power cables. The bottom tube should be the last tube
connected so that it can be easily connected to the control box.
10. Mount the control box in a location where the last power cable can easily connect to it. This step is going to be unique to each installation based on how your
television is mounted.
11. Once the control box is mounted, connect the last lead power cable to your control box.
12. Now connect the infrared (IR) receiver to the control box, and mount it in a location where it is free from any interference and has a clear line of sight.

NOTE: The included IR receiver works together with the included remote to operate the kit, and allows you to keep your control box hidden.
13. Lastly, plug the included power supply into a standard wall outlet and connect the mini jack to the control box.
14. Now that your kit is installed and powered turn the kit on using the included remote and test the kit again for full functionality.

NOTE: If your remote is not controlling the kit properly, you may need to adjust the IR receiver to achieve the best result.