Accell MPC-LNK - Manual (Page 11)

-10-
MPC-816 Series ~ 8-Bit CPU Controller ~
MPC-816K
Main CPU Board 8 Outputs, 16 Inputs
[Characteristics]
This is a CPU board equipped with the I/O for control. By its installed interpreter (TNYFSC), programming is possible
in a BASIC-like environment. In spite of its compactness, it is equipped with 2M-bit flash ROM, and its program area
of about 2000 steps can be used without any procedure such as ROM conversion or compiling. Also, a user RS-232C
(isolated) is equipped, making it applicable to communication-involving use.
[Specification]
Power source: DC 12V~24V battery-retained for 7 years (w/o external power supply at room temperature).
CPU: KL5C80A16, 7.37 MHz, 1M SRAM + 2M FROM.
Control I/O: 8-point open collector output, 16-point photocoupler input.
Self-consumed current: 110 mA (380 mA power source installed)
[Accessories] (1) Housing (PS-D4C50) JAE *1
(2) Power connector (H4P-SHF-AA) JST *1
(3) Contacts (BHF-001T-0.8SS) JST *4
MIF-816K
Bus Interface Board 8 Outputs, 16 Inputs
[Characteristics]
This is the first expansion board of MPC-816. It is a bus interface of expanded I/O: MIO-816 and also equipped with
the control I/O at the same time. Also, a 16-pin connector J5 becomes a pulse output port if the Z version is selected on
MPC-816, enabling simple control of a pulse motor, etc. Also, MPC-SET (EX) is the set of MPC-816 and MIF-816
being packed in a case.
[Specification]
Power source: DC 12V~24V (for I/O control).
Control I/O: 8-point open collector output, 16-point photocoupler input, 4-axis pulse output port.
Consumed current: 30 mA
[Accessories] (1) Housing (PS-D4C50) JAE *1
(2) Power connector (H4P-SHF-AA) JST *1
(3) Contacts (BHF-001T-0.8SS) JST *4
(4) Connector (HIF-3BA-16D-2.54R) Hirose *1
(5) Spacers (MSPLS-7) *4
MIF-816AD
Bus Interface Board with AD/DA 8 Outputs and 12 Inputs
3CH A/D 1CH D/A
[Characteristics]
This is the first expansion board of MPC-816 and has almost the same specification with MIF-816. Differences from
MIF-816 are that it is equipped with a 12-bit A/D and D/A converter and that J5 has no ZCW and ZCCW output. It is
best for small-scale analog test output circuits.
[Specification]
Power source: DC 12V~24V (for I/O control). DC 5V (for A/D and D/A). Internal V can be also used.
Control I/O: 8-point open collector output. 12-point photocoupler input.
3-axis pulse port (w/o ZCW and ZCCW). 3-CH analog input.1-CH analog output.
Consumed current: 260 mA (150 mA if A/D and D/A are externally supplied.)
[Accessories] (1) Power connector (H4P-SHF-AA) JST *1
(2) Contacts (BHF-001T-0.8SS) JST *4
(3)Spacers (MSPLS-7) *4
MBK-816
Touch-Panel Interface Board RS-422(485) 2CH
[Characteristics]
This is an I/F board for a touch panel display for MPC-816. It is compatible with Memo-Link of Digital Corp. as of
March 99, and it can be interfaced with the panel by using only ON/OFF/SW() commands from the MPC-816 side.
[Specification]
Power source: DC 12V~24V (for panel communication)
Control I/O: RS-422(485) 2CH
Consumed current: 200 mA
[Accessories] (1) Power connector (H4P-SHF-AA) JST *1
(2)Contacts (BHF-001T-0.8SS) JST *4
(2)
(1)
(3)
(4) (5)
(2)
(1)
(3)
(3)
(1) (2)
(1) (2)