PATLITE PSE - Manual (Page 2)

5 6
7 8
1
1
3
3
4
4
2
2 Before mounting the product, drill holes into the mounting
surface in accordance to the dimensional drawing. Insert the Power Cord into
the wire hole before
inserting the body into the
mounting hole. Properly wire to the
power supply.
( → Wiring Example
(P.7)) Fasten with the (M4) nuts
included and tighten.
(Recommended Torque：
1.4 N・m)
P o i n t
OK !
What
voltage? DC?
AC?
・ Thinner
・ Alcohol
・ Gasoline
・ Oil
What voltage?
What ampere?
φ
50
120°
120°
32
6
(13)
(43)
Notice to
Customer
Notice to
Contractor
Thank you very much for purchasing our PATLITE product.
Request the installation and wiring be performed by a professional contractor if construction work is involved.
Prior to installation, read this manual thoroughly before using this product to ensure correct use.
After reviewing this manual, if there are any questions regarding this product, please contact the nearest PATLITE office listed on the back cover of this manual.
Read this manual carefully prior to installation.
Be sure to return this manual to the customer.
Use only the specified replacement parts listed in this
manual. Install an external fuse between the power supply and
product to protect the internal circuitry.
( → Installation and Wiring (P.6)) 5
This product is useful for warning indications by flashing,
and can be used on equipment, in factories and other applications.
Request the installation and wiring be performed by a
professional contractor if construction work is involved.
Failure to comply may result in fire, electric shock or
falling from high places may occur.
Do not, by any means, disassemble or modify this product.
This product contains high voltage, which is very dangerous,
so only remove replacement parts.
Replacement parts are removable.
To ensure proper safety while using the Signal Light,
observe the following:
・Perform periodic pre-maintenance.
( → Inspection (P.7))
・As a precaution against problems occurring, use this
product together with other equipment.
6
Do not look directly into the light source during
operation of this product.
The excessive brightness may impare vision.
Properly secure this product to prevent from falling,
particularly from high places. Failure to comply may
result in death, serious injury, or product damage.
To prevent from short-circuits, electric shock or damage,
observe the following:
・Be sure the power is disconnected before replacement
(Globe exchange, etc.) or repair.
・Please use this product in a properly maintained
condition.
(If parts such as the body or globe are damaged, they
should be repaired.)
WARNING Failure to observe the following may result in death or serious injury.
To ensure safety when this product is installed onto
equipment, observe the following.
・Do not use this product as leverage when climbing up
onto the equipment. Failure to comply will result in
falling from a high place, or damage to the product.
・When performing tasks such as opening covers on the
equipment, be careful not to snag anything on this
product. Failure to comply will result in product
damage.
CAUTION Failure to observe the following may result in personal injury or product damage.
Do not apply excessive torque or
strong shock to this product.
Failure to comply will result in
product damage.
・The images in this manual may vary in comparison to the actual product
and are only for the purpose of illustration.
・Store this manual in a location for future reference.
DC 12 / 24 V M1 AC 100 / 200 / 230 V M2
R Red
The luminescence color is indicated.
Y Amber G Green B Blue
Due to LED and Globe color compatibility,
changing the Globe cannot be done without
the LED Unit being changed as well.
PSE-M1-R ・Rated Voltage … DC 12 / 24 V
・Color …………… Red Model No. ↓ ↓ PSE-
Model Color
-
Rated Voltage Model Number Example
M1
M2
φ82
LED Unit
Cut Lens
Globe
Body
Power Wire
Nameplate
Mounting Bolt
(M4 x3)
Wire length : 340
Cord Diameter : Approx φ7
Red
Green / Yellow
White
Black
Black
Wire length : 340
Cord Diameter : Approx φ7
(Units: mm)
123
13
50
73
Power Cord Specifications
O-ring
Accessories
Nuts (M4) x3 Spring Washer x3 Washer x3
The following illustrates the internal block diagram for the Signal Light. Use it as reference when wiring.
Power
supply wire
Power
supply wire
LED Circuit Flashing Circuit Power Supply Circuit
LED
PSE-M2
Built-in Fuse
(Not Replaceable)
Flashing
Circuit
：Current flow
during LED
flashing
Power
Supply
Circuit
AC
100 / 200 / 230 V
Earth Wire
LED Circuit Flashing Circuit
Power
supply wire
Power
supply wire
LED
PSE-M1
Built-in Fuse
(Not Replaceable)
Flashing
Circuit
DC 12 / 24 V
(Note) The diagram is only an example.
：Current flow
during LED
flashing
Install in an upright position when placed in a wet
environment.
Failure to comply will result in a decrease in
waterproofing performance.
(Protection Rating: IP23)
Do not remove the Cut Lens for any reason.
Failure to comply may result in electric shock.
Use a soft cloth, etc., dampened with water to wipe the
main Signal Light unit.
(Do not use cleaners containing chemicals such as
thinner, alcohol, gasoline or oil.)
Do not use the product with the O-ring removed.
Failure to comply will result in a decrease in
waterproofing performance.
Prior to wiring, ensure the power
supply is disconnected from the
Signal Light.
Do not pull the power cord or
push it inside the body.
WARNING
Verify the power supply voltage
and whether it is direct current
or alternating current.
CAUTION
The following requirements are necessary for proper
installation.
・Install the Signal Light where
excessive vibration is not present.
・Install the Signal Light on a sturdy surface.
・Install the Signal Light on a level surface.
To protect the power supply and other internal circuitry,
be sure to install an external fuse.
( → Wiring Example (P.7))
Use a fuse to match the appropriate rating for the
equipment being connected.
（A 2A fuse is built-inside the product.）
( → Wiring Example (P.7))
Be sure to ground the earth wire.
Failure to comply may result in
electric shock or possible fire.
( )
M2
The following is the procedure for installing this product.
(Note) Because the figure is an illustration, the
mounting and distribution hole positions
may vary from actual dimensions.
Refer to the dimensional drawing for
proper position and sizes.
PSE
Installation Surface
Power Wire
・Prior to drilling, the work will become easier if marking the
holes with a punch, etc., is done first.
Mounting Bolt (x3)
(Scale: 4/5)
If using a copier machine, increase the size to 1.25 times (125%) to scale
for actual size. (Ensure that it is actual size)
Hole Installation (φ5x3 Holes)
Wire Hole (φ10)
（Units：mm）
Nameplate position
Dimensional drawing
The wiring example is indicated for every model.
If the Signal Light is being used under special conditions and there are any questions, contact our PATLITE office prior to performing any wiring.
PSE
External fuse
DC 12 / 24 V
1
2
1 A 2A fuse is built-inside the product. 2 Use an external fuse with the recommended rating for the product being used.
Product specifications DC 12 / 24 V Model PSE-M1
Power
supply wire
Power
supply wire
Red
Black
Product specifications Model AC 100 / 200 / 230 V PSE-M2
External
fuse
PSE
AC 100 /
200 / 230 V
2
1
Power
supply wire
Power supply wire
Earth Wire
3
Green Yellow
3 Be sure to ground the earth wire.
White
Black
To ensure safe operation, it is recommended to perform the following.
If a problem occurs, check the following table to remedy the problem before calling for service.
Inspection Item
Is the LED flashing?
Check the outside appearance.
Is there any damage?
Refer to the Troubleshooting section ( → P.7) if it does not flash.
Inspection Repair
Problem Where to Check Solution
Is the wiring properly connected?
Is the fuse blown? If the external fuse is blown, replace it.
7
Is the power supply at the correct voltage? Be sure to use this product at its rated voltage.
The LED
does not flash.
Is the mounting nut loose? If the nut is loose, tighten it with the recommended torque. (→ Installation and Wiring (P.6)) 5
If there is any external damage such as cracks, or missing parts, stop using
the Signal Light and replace the necessary parts or the Main Unit. (→ Replacement Parts (P.8))
9
Refer to Installation and Wiring (→ P.6) to double-check the wiring connection. 5
If the problem is not corrected, even after the above remedies have been performed, use the table below to make detailed notes of the
product, its problem, and then contact either the place of purchase or your nearest PATLITE Sales Representative.
●The place of purchase ●A PATLITE office (Refer to the back cover of this manual.)
Product Details
Product name
Model
LED Signal Light
（→ Model Number Configuration （P.5））
Purchase Date
Symptoms of Problem
/ /
With as much detail as possible 2
・This product complies with EN regulations and shows the CE symbol.
・This product conforms to the RoHS directive (DIRECTIVE 2011/65/EU).
Power
Consumption Model Rated Voltage
Installation
Location Mass
Indoor or
Outdoor Use
IP
Protection
Rating
IP23
Maximum
surrounding
air temperature
rating
60℃
0.3kg
0.35kg
Max. 2.4W
Max. 3.2W
DC 12 / 24 V
AC 100 / 200 / 230 V
PSE-M1
PSE-M2
Flashing Frequency
110 ±10 times/min.
(Triple-flash)
(Note) ・Dimensions, specifications and structure are subject to change for improvement without notice.
・ Responsibility will not be taken if failure or damage, etc., is caused by handling in contrary to the warnings
and notes written in this operation manual.
SZ-210
Rubber Gasket
Model
Product name
This product includes the following option parts. For details,
refer to our company website. The following are replacement parts available for this product.
For further details, refer to our company website.
Part Name Remarks
Globe Red RS The Globe (Red) is a single article.
Globe Amber RS The Globe (Amber) is a single article.
Globe Green RS The Globe (Green) is a single article.
Globe Blue RS The Globe (Blue) is a single article.
O-ring,PES,RU etc. The O-ring is a single article.
Since a different Globe and the LED Unit are mounted by model (color),
change of the luminescent color by exchange of only a Globe cannot be
performed. Use the Mount Rubber SZ-210
accessory to increase the IP rating
to IP55.
(For Upright Installation)
3463-B
'13.4.AUTO
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Safety Precautions
Signal Light Application
Safety Precautions 1
Instruction Manual Objective
Model Number Configuration 2
Part Names and Outer Appearance 3
Block Diagram 4
Installation and Wiring 5
Installation
Wiring Example
Inspection 6
Troubleshooting 7
Specifications 8
Replacement Parts 9 Option Parts 10
LED Signal Light
INSTRUCTION MANUAL
[ Maintenance Version ] Installation Operation Maintenance
Model
PSE