EnzoTech SNBW-REV.A - Manual

CAUTION!
Total thread length greater than 6.5 mm / 0.256 inch will cause
damages to the top (cap). Enzotech will not guarantee this
type of damage due to human factor.
6.5 mm/0.256 inch
1 2 3 4 5 6 7 8 9 10
http:// www.enzotechusa.com http://www.enzotechnology.com
Precautions
-Test product for leakage away from system before installing.
All products are leak-tested prior to shipping; however,
damage can occur during shipping and subsequent handling.
Once no leakage is confirmed, proceed with the installation
and use. Always check your circuit for leaks prior to
powering-up system.
-Never use harsh chemicals to clean your water block.
Alcohol or any other harsh solvent may cause damage to
certain materials used in the manufacturing of the water
block.
-keep this product and its associated installation items away
from children.
6.WARRANTY
Our products are guaranteed for 12 months from the date of
delivery to the final user against defects in materials or
workmanship. During this period, Product will be repaired or
have parts replaced, provided; (I) the products is returned
to the agent from which it was purchased: (II) the product
has not been misused, handled carelessly or other than in
accordance with any instructions provided with respect to
its use. This guarantee does not confer rights others than
those expressly set out above and does not cover any claims
for consequential loss or damage. This guarantee is offered
as an extra benefit and does not affect your statutory rights
as a consumer.
7.Important Disclosures:
Enzotech is not responsible for any damages due to external
causes,including but not limited to, improper use, problems
with electrical power, accident, neglect, alteration,repair,
improper installation, or improper testing.
1.Features
1)High density stagger fin design, provides maximum surface
exposure area for superior cooling performance.
2)Water block’s base is machined to .0003 per inch
run-out which optimizes surface contact and maximizes
thermal conductivity performance.
3)Multiple mounting systems for maximum installation versatility.
4)Compatible with most recent SLI motherboards.
5)100% leak tested and inspected direct from factory.
2.Specification
1.Dimension(L x W x H): 59.2x53.1x17.5mm
2.Base(L x W x H): 45x35x7.5mm
3.Total Weight:160g
3.Components
1.Common Components
a)One (1)User’s Manual
b)One (1)Northbridge Water Block
c)One (1)O-Ring(Pre-Assembled)
d)Two (2)1/2” HI-Flow Host Barbs
e)Two (2)Tube Clamps
f)One (1)Artic Silver Ceramique
Thermal Grease (OEM)
g)One (1)Allen Wrench #2
h)One (1)Sponge (For Flip Chip Users)
I)Four (4)M3X10L Screws
One (1)Spring Mount Pack
One (1)Wire Clips Pack
One (1)Hard Mount Pack
4.Installation
(1).Spring Mount Installation
Spring Mount Pack
A) Two (2) M3x30 Screws
B) Four (4) Fiber Washers
C) Two (2) Tension Limiters
D) Two (2) Thumb Screw s
E) Two (2) Springs
F) Two (2) Nuts
1. Remove old fan/heatsink from motherboard
2. Clean the surface of the northbridge chipset and apply the
provided thermal compound evenly on the chipset surface
3. Install the two Mounting Posts/M3x30 Screw (A) as shown in the
schematic and fasten them with Nuts (F) and Washers(B)
4. Install the Sapphire Northbridge Waterblock on the northbridge
chipset. Install the Spring (E), Tension Limiters(C), and Thumb
Screw(D)
5. Gradually and alternatively fasten the Thumb Screw until the
proper tension is reached. DO NOT OVERTIGHTEN THE
THUMB SCREW
(2).Wire Clip Installation
If the mounting bracket does not interfere with the components on
the motherboard, then it is not required to remove the mounting
bracket.
If the mounting bracket does interfere with components on the
motherboard, please remove the mounting bracket, use the
spacer(B) and M3x10L Screw(C) to fasten the housing with base
plate.
Wire Clips Pack
A) Two (2) Wire Clips
B) Four (4) Spacers
C) Four (4) M3x10L Screws
1. Remove old fan/heatsink from motherboard.
2. Clean the surface of the northbridge chipset and apply the
provided thermal compound evenly on the chipset surface
3. Install the Sapphire Northbridge Waterblock on the
northbridge chipset
4. Remove the top cover and mount the bracket.Next,fasten
m3x10L screws to the base. Insert the hooks of the wire clips
underneath the loop of the MB.
(3).Hard Mount Installation
Hard Mount Pack
A) Two (2) M3x19 Screws
B) Four (4) Fiber Washers
C) Two (2) Nylon Spacers
D) Two (2) Nuts
1. Remove old fan/heatsink from motherboard
2. Clean the surface of the northbridge chipset and apply the
provided thermal compound evenly on the chipset surface
3. Insert Screws (A) thru the top of the Sapphire Northbridge
Waterblock.
4. Fasten Nylon spacers(C) and Washers(B), Place the
waterblock on the chipset and fasten it from the back of the
motherboard using the provided metal nuts (D)
Fasten the nuts alternatively and incrementally to maintain
as even pressure on the chipset as possible.
User’s Manual
(English Version)
SNBW-REV.A
a
b
d
e
f g
h
c
I
http:// www.enzotechusa.com http://www.enzotechnology.com
User’s Manual
(English Version)
SNBW-REV.A