Audio-Technica AT898 - Manual (Page 2)

AT898
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0181-01
Specifications
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis LEGEND
Frequency in Hertz
Response in dB
10 dB
100 50 200 10k 5k 1k 500 2k 20k
Roll-off
frequency response: 200–15,000 Hz
polar pattern
Fixed-charge back plate, permanently
polarized condenser
Cardioid
200-15,000 Hz
80 Hz, 12 dB/octave
Phantom: –43 dB (7.0 mV) re 1V at 1 Pa
Battery: –46 dB (5.0 mV) re 1V at 1 Pa
Phantom: 200 ohms
Battery: 250 ohms
Phantom: 131 dB SPL, 1 kHz at 1% T.H.D.
Battery: 115 dB SPL, 1 kHz at 1% T.H.D.
Phantom: 100 dB, 1 kHz at Max SPL
Battery: 84 dB, 1 kHz at Max SPL
63 dB, 1 kHz at 1 Pa
11-52V DC, 2 mA typical
1.5V AA/UM3
0.4 mA / 1200 hours typical (alkaline)
Flat, roll-off
Microphone: 0.9 g (0.03 oz)
Power module: 102 g (3.6 oz)
Microphone: 23.0 mm (0.91") long,
5.3 mm (0.21") diameter
Power module: 145.0 mm (5.71") long,
21.0 mm (0.83") diameter
Power module: Integral 3-pin XLRM-type
3.0 m (9.8') long (permanently attached
to microphone), 2.0 mm (0.08") diameter,
2-conductor, shielded cable with TA3F-
type output connector that mates with
TB3M-type jack on power module
M30
AT8537 power module; AT8439 cable
clip; clothing clip base; viper clip base;
magnet clip base and plate with lanyard;
three single mic holders; two double
mic holders; two windscreens; battery;
protective carrying case
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio 1
Phantom power requirements
Battery type
Battery current / life
Switch
Weight
Dimensions
Output connector
Cable
Audio-Technica case style
Accessories furnished
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm 2 = 10 microbars = 94 dB SPL
1 Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
skin. For best results, ensure that pin ends rest on outside of clothing.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Architect’s and Engineer’s Specifications
The microphone shall be a fixed-charge condenser. It shall have a
cardioid polar pattern with a uniform 120° angle of acceptance and
a frequency response of 200 Hz to 15,000 Hz. The microphone shall
operate from an external 11V to 52V DC phantom power source or,
alternatively, from a 1.5V AA/UM3 battery. It shall be capable of handling
sound input levels up to 131 dB (phantom) or 115 dB (battery) with a
dynamic range of 100 dB (phantom) or 84 dB (battery). Nominal open-
circuit output voltage shall be 7.0 mV (phantom) or 5.0 mV (battery) at
1 V, 1 Pascal. Output shall be low impedance balanced (200 ohms –
phantom, 250 ohms – battery).
The microphone shall have a 3 m (9.8') permanently attached miniature
cable terminating in a TA3F-type output connector. The output connector
shall connect to a TB3M-type jack on the included power module. The
power module shall contain a recessed switch to permit choice of flat
response or 80 Hz low-frequency roll-off. The output of the power module
shall be a 3-pin XLRM-type connector.
The microphone shall be 23.0 mm (0.91") long and have a diameter of 5.3
mm (0.21"). Weight shall be 0.9 grams (0.03 oz). The microphone shall
include a power module, a cable clip, a clothing clip base, a viper clip
base, a magnet clip base and plate with lanyard, three single mic holders,
two double mic holders, two windscreens, a battery and a protective
carrying case. Finish shall be low-reflectance black.
The microphone shall also be available with a 1.4 m (55") permanently
attached miniature cable terminated for use with Audio-Technica UniPak
®
body-pack transmitters and a variety of other manufacturers’ wireless
systems. The wireless models’ dimensions, polar pattern and included
accessories (excluding power module and battery) shall be identical
to those of the wired model. The microphone shall also be available
unterminated.
The Audio-Technica AT898 is specified.
The Audio-Technica [AT898cW]; [AT898cL4]; [AT898cT4]; [AT898cT5]
(wireless version) is specified.
The Audio-Technica AT898c (unterminated) is specified.
401