Vaddio SDI Slot Card for Vaddio ClearVIEW HD-18/20 User Manual
Page 8
WallVIEW CCU HD-18 HD-SDI
WallVIEW CCU HD-18 HD-SDI Manual 341-988 Rev. A
Page 8 of 26
First Time Set-up with the WallVIEW CCU HD-18 HD-SDI:
WallVIEW CCU HD-18 HD-SDI was designed to be exceptionally easy to use and operate. There is
documentation at the back of the manual for pin-outs for all of the connectors on the WallVIEW CCU HD-
18 HD-SDI System.
Getting Started:
First, set up the HD/SD-SDI output resolution for the camera, baud rate and image flip.
Figure 8: Dip Switch and Video Output Resolution Setting Options Label for the HD-18 Camera
• IR 1, 2 & 3: These settings, using switches 1 & 2, determine the IR frequency of the IR remote control
that was supplied with your camera. The IR remote has the capability of operating up to three different
PTZ cameras from one remote, using the selector buttons at the top of the remote.
• IR Out: The IR output is sent on the RJ-45, RS-232 jack on the back of the camera. NOTE: When
using the Quick-Connect CCU, the IR output must be in the Off position (up).
• Baud Rate: The options for baud rate are either 9600 or 38,400 for RS-232.
• SD Output Frequency: Select either NTSC or PAL as the output for the camera’s SD signal that is
transmitted on the BNC connector.
• SD Output Size: Three options are available for the SD output, select from crop, squeeze or letterbox.
NOTE: These switches adjust only the composite SD output, not the SDI output, which will remain 4:3.
• Image Flip: Turning Image Flip on (switch down), will allow the camera to be inverted.
• Test Bars: Turning this switch on will override the camera video output and send test video bars from
the camera to the CCU to allow more accurate setting of the video level at the CCU.
• Switch 10: This switch is unused, and should be left in the OFF position.
RS-232 Cabling
For RS-232, use a standard CAT 5e cable (568B termination for RJ-45 connectors) from the RS-232 port
on the back of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected
to a third-party control system (such as AMX or Crestron), a DB-9 to RJ-45 adapter cable is supplied with
the camera for RS-232.
IR OUT – Switch 3
When operating the HD-18 camera with the Quick-Connect CCU, the IR Output must be set to the OFF
position on the back of the camera. If it is not turned off, it will interfere with proper operation of the PTZ
camera.
INSTALLATION
The WallVIEW CCU HD-18 HD-SDI product was specifically designed for installation on a vertical wall
surface with Coax and CAT 5e cable connectivity for Video, Power and Control signaling (one coax and
two CAT 5e cables). Installation is simplified in that no custom cables and no power outlets are required
near the camera bracket. The use of “pass-thru” RJ-45 connectors should not be used (see notice on
page 2).
IR 1
1 & 2 UP
ON
SD
NTSC
SD
PAL
SD 4:3
6 & 7 UP
SD
LB
IMAGE
FLIP
OFF
ON
ON
DIP SWITCH SETTINGS
8
1
2
3
4
5
6
7
9
10
HD VIDEO SELECT
720p/59.94
1080i/59.94
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1080p/59.94
1080p/60
720p/50
1080i/50
1080p/50
2
1
5
4
3
7
6
8
10
9
ON
IR 2
ON
IR 3
ON
IR
OUT
OFF
9600
bps
38400
bps
SD
SQ
TEST
BARS
OFF
10
OFF
480i/29.97
1080p/25
1080p/30
576i/25