Silverline 2500W Angle Grinder 230mm - Manual (Page 6)

www.silverlinetools.com
5
2500W Angle Grinder 124445
• Always refer servicing to qualified service personnel. Never remove any
part of the casing unless qualified to do so; this unit contains dangerous
voltages
• Use of a residual current device will reduce the risk of electric shock
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE EARTH PIN OF A 13A
PLUG. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose them to
rain. Provide adequate surrounding work space and keep the area well
lit. Do not use power tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of
an explosive nature. When using power tools, avoid contact with any
earthed items such as pipes, radiators, cookers, refrigerators, metal
baths and taps
Protect yourself from vibration
• Hand-held power tools may produce vibration. Vibration can cause
disease. Gloves may help to maintain good blood circulation in the
fingers. Hand-held tools should not be used for long periods without a
break
Maintain your power tool
• Ensure all ventilation holes are kept clear at all times, otherwise
overheating and fire may occur
Always disconnect
• Before changing fittings or accessories, always disconnect the tool from
the power source
Switch off before connecting
• Ensure the power tool is switched off before connecting to the power
source. If the power tool stops unexpectedly, turn the power switch to
OFF
Do not abuse the power cable
• Be sure the cable / extension cable is in good condition. Always have
a damaged cable / extension cable replaced at an authorised service
centre before using. Never pull the cable to disconnect it from the power
socket. Never carry the tool by its cable. Keep the cable away from damp,
heat, oil, solvents, and sharp edges
Do not modify the power tool
• Do not modify the power tool in any way as this could result in serious
injury and may invalidate its guarantee
Do not leave the tool running unattended
• Always wait until the tool has completely stopped functioning and has
been unplugged before leaving it unattended
Grinding Tool Safety
• Always wear appropriate personal protective equipment. When using a
grinder, safety goggles, ear defenders and dust masks should be worn
• Do not attempt to cut or grind magnesium or any alloy that has high
magnesium content
• Use plain or centre recessed cutting or grinding discs of a size stated
in this instruction manual. Attempting to use any other accessory or
attachment is extremely dangerous and could lead to serious injury
• The maximum speed of the cutting/grinding disc should always be higher
than the maximum speed of the machine to which they will be attached
• Use the correct cutting/grinding disc for the job. Stone/ metal-working
discs and cutting/ grinding discs are not interchangeable
• Do not allow discs to become wet or oil soaked. If you suspect that a disc
has degraded in storage DO NOT USE
• Inspect cutting/grinding discs before use. If a disc is damaged in any
way (chipped, fractured etc) DO NOT USE. Dispose of disc and replace.
Damaged discs can spontaneously shatter
• Do not attempt to make cuts that exceed the maximum cutting depth of
the disc
• Do not use any form of spacers to make an incorrect disc fit your machine
• Ensure that the cutting/grinding disc is fitted correctly and securely
before use. Run the machine with the disc fitted, but no load, for
30 seconds before attempting to cut/grind. If excessive vibration is
encountered, stop the machine and correct the cause before use
• Never operate a grinder without its guards in place
• Do not stand in line with the cutting/grinding disc when in use
• Do not operate the spindle lock while the grinder is running
• Beware that the machine will ‘run on’ for some time after being switched
off. Allow the machine to stop itself. Do not stop the machine by holding
an object against the disc. NEVER place the grinder down until the disc
has completely stopped
• A grinding disc will wear as it is used, reducing its size. If a disc becomes
too small to work with easily, replace it
124445_Z1MANPRO1.indd 5 27/06/2011 17:01