Muxlab CCTV Power-Thru Converter Balun - Manual

© MuxLab Inc.
Specifications
Environment Baseband composite video; NTSC, PAL, SECAM
Devices 12VDC analog CCTV cameras
Transmission Transparent to the user.
Video
Bandwidth DC to 8 MHz.
Impedance Input: 75 ohms (BNC); Output: 100 ohms (RJ45)
Maximum Input 1.1Vp-p
Insertion Loss Less than 2 dB per pair over the frequency range from DC to 8 MHz
Return Loss Greater than 15 dB over the frequency range from DC to 8 MHz
Common Mode Rejection Greater than 40 dB @ 8 MHz
Max. Distance – Colour Cat 3 –1,200 ft (365m); Cat 5e/6 – 2,200 ft. (670m)*
*Certain models of DVR may yield shorter distances of 1,000 to 1,500 ft
Max. Distance – Black & White Cat 3 –1,500 ft (457m); Cat 5e/6 – 2,500 ft (762m)
Remote Power (i.e.; 24 VAC, 28 VAC)
Wiring Remote low voltage power supported via three (3) twisted pairs. A Class II
power supply is recommended.
Input Voltage 13 to 30VAC/DC
Output Voltage 12 VDC
Output Current 400 mA
Max. Distance – Colour 795 ft. (242m) with 24VAC or 1,113 ft. (339m) with 28VAC*
*With a Maximum Consumption of 400mA
Max. Distance – Black & White 1,586 ft. (478m) with 24VAC or 2,220 ft. (677m) with 28VAC*
*With a Maximum Consumption of 200mA
Mechanical & Environmental
Cable – UTP 24 AWG or lower solid copper twisted pair wire impedance: 100 ohms at 1 MHz
Maximum capacitance: 20 pf/foot. Attenuation: 6.6 dB/1000 ft at 1 MHz
Cable – Coax Impedance: 75 Ω at 1 MHz. (RG59/U). Max. 25 ft. of coax allowed end to end.
Connectors Combined signals: RJ45 Video: BNC-male 8” mini-coax lead
Power: 2-wire 18AWG lead
Pin Configuration*
*Reverse polarity sensitive Signal RJ45 Pin Cable Lead
Color
Power A 1 (common with 3&5) Red
Power B 2 (common with 4&6) Black
Power A 3 (common with 1&5) Red
Power B 4 (common with 2&6) Black
Power A 5 (common with 1&3) Red
Power B 6 (common with 2&4) Black
Video BNC Center (Tip) 7 [T] opposite to 500000 Mini-coax
Video BNC Ground (Ring) 8 [R] opposite to 500000 Mini-coax
Temperature Operating: 0° to 55°C. Storage:-20° to 85°C. Humidity: up to 95%
Enclosure ABS fire retardant plastic
Dimensions 2.4” (6.1cm) x 2.25” (5.5cm) x 1.0” (2.5cm) plus cable leads; 8” (20cm) for
video; 10” (25.4cm) for power lead
Weight 3.0 oz (85 gms)
Warranty Lifetime
Order Information 500024-CNV CCTV Power-Thru Converter Balun
Tel.: +1 (514) 905-0588 Fax: +1 (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: [email protected] URL: www.muxlab.com
94-000376-A SE-000323-A
CCTV Power-Thru Converter Balun (500024-CNV)
Quick Installation Guide
Introduction
The CCTV Power-Thru Converter Balun (500024-CNV) allows video and remote
power to be transmitted via one 4-pair Cat 5e/6 cable, thus eliminating the need to
install multiple cables for more efficient cabling in the analog CCTV security and
surveillance environment. Furthermore the product converts 24VAC to 12VDC @
400mA to allow 12VDC cameras to be remotely powered from a central 24VAC
CCTV power supply. The CCTV Power-Thru Converter Balun works in
conjunction with MuxLab’s CCTV Power-Thru Balun (500024), Passive CCTV
Power Integrator Hub (500136), Passive CCTV Hub (500130) and LongReach II
Active Balun (500124) and Hub (500126, 500127) for a complete cabling solution.
Installation
Pre-Installation Checklist:
Note: For regulatory reasons, use of a Class II power supply is
recommended and may be required with the use of this product in some
regions.
1. The CCTV Power-Thru Converter Balun (500024-CNV) is designed to be
installed at the camera side.
2. Ensure the CCTV equipment and remote power supply is turned off.
3. One (1) twisted pair is required for the camera video signal. Three (3) twisted
pairs are required for remote power.
4. Verify that the cable length is within MuxLab specifications. The
maximum distance for 24VAC and remote power is 795 ft. (242m) at the
maximum allowable power consumption of 400mA.
5. Identify the pin configuration of the balun by checking the product label or the
specification section of this installation guide.